EVB9S08DZ60 Freescale Semiconductor, EVB9S08DZ60 Datasheet - Page 366

• Manufacturer Part Number: EVB9S08DZ60
• Description: BOARD EVAL FOR 9S08DZ60
• Manufacturer: Freescale Semiconductor
• Type: MCUr

Specifications of EVB9S08DZ60

• Contents: Module and Misc Hardware
• Processor To Be Evaluated: S08D
• Data Bus Width: 8 bit
• Interface Type: RS-232, USB
• Silicon Manufacturer: Freescale
• Core Architecture: HCS08
• Core Sub-architecture: HCS08
• Silicon Core Number: MC9S08
• Silicon Family Name: S08D
• Kit Contents: Board Cables CD Power Supply
• Rohs Compliant: Yes
• For Use With/related Products: MC9S08DZ60
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Chapter 17 Development Support
17.4.3.7
This register can be read or written at any time.
366
Reset
RWBEN
DBGEN
RWAEN
BRKEN
Field
ARM
RWA
RWB
TAG
W
7
6
5
4
3
2
1
0
R
DBGEN
Debug Module Enable — Used to enable the debug module. DBGEN cannot be set to 1 if the MCU is secure.
0 DBG disabled
1 DBG enabled
Arm Control — Controls whether the debugger is comparing and storing information in the FIFO. A write is used
to set this bit (and ARMF) and completion of a debug run automatically clears it. Any debug run can be manually
stopped by writing 0 to ARM or to DBGEN.
0 Debugger not armed
1 Debugger armed
Tag/Force Select — Controls whether break requests to the CPU will be tag or force type requests. If
BRKEN = 0, this bit has no meaning or effect.
0 CPU breaks requested as force type requests
1 CPU breaks requested as tag type requests
Break Enable — Controls whether a trigger event will generate a break request to the CPU. Trigger events can
cause information to be stored in the FIFO without generating a break request to the CPU. For an end trace, CPU
break requests are issued to the CPU when the comparator(s) and R/W meet the trigger requirements. For a
begin trace, CPU break requests are issued when the FIFO becomes full. TRGSEL does not affect the timing of
CPU break requests.
0 CPU break requests not enabled
1 Triggers cause a break request to the CPU
R/W Comparison Value for Comparator A — When RWAEN = 1, this bit determines whether a read or a write
access qualifies comparator A. When RWAEN = 0, RWA and the R/W signal do not affect comparator A.
0 Comparator A can only match on a write cycle
1 Comparator A can only match on a read cycle
Enable R/W for Comparator A — Controls whether the level of R/W is considered for a comparator A match.
0 R/W is not used in comparison A
1 R/W is used in comparison A
R/W Comparison Value for Comparator B — When RWBEN = 1, this bit determines whether a read or a write
access qualifies comparator B. When RWBEN = 0, RWB and the R/W signal do not affect comparator B.
0 Comparator B can match only on a write cycle
1 Comparator B can match only on a read cycle
Enable R/W for Comparator B — Controls whether the level of R/W is considered for a comparator B match.
0 R/W is not used in comparison B
1 R/W is used in comparison B
0
7
Debug Control Register (DBGC)
ARM
0
6
Table 17-4. DBGC Register Field Descriptions
Figure 17-7. Debug Control Register (DBGC)
MC9S08DZ60 Series Data Sheet, Rev. 4
TAG
0
5
BRKEN
0
4
Description
RWA
0
3
RWAEN
0
2
Freescale Semiconductor
RWB
1
0
RWBEN
0
0