EVB9S08DZ60 Freescale Semiconductor, EVB9S08DZ60 Datasheet - Page 32

• Manufacturer Part Number: EVB9S08DZ60
• Description: BOARD EVAL FOR 9S08DZ60
• Manufacturer: Freescale Semiconductor
• Type: MCUr

Specifications of EVB9S08DZ60

• Contents: Module and Misc Hardware
• Processor To Be Evaluated: S08D
• Data Bus Width: 8 bit
• Interface Type: RS-232, USB
• Silicon Manufacturer: Freescale
• Core Architecture: HCS08
• Core Sub-architecture: HCS08
• Silicon Core Number: MC9S08
• Silicon Family Name: S08D
• Kit Contents: Board Cables CD Power Supply
• Rohs Compliant: Yes
• For Use With/related Products: MC9S08DZ60
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Chapter 2 Pins and Connections
Whenever any reset is initiated (whether from an external signal or from an internal system), the RESET
pin is driven low for about 34 bus cycles. The reset circuitry decodes the cause of reset and records it by
setting a corresponding bit in the system reset status register (SRS).
2.2.4
While in reset, the BKGD/MS pin functions as a mode select pin. Immediately after reset rises, the pin
functions as the background pin and can be used for background debug communication. While functioning
as a background or mode select pin, the pin includes an internal pull-up device, input hysteresis, a standard
output driver, and no output slew rate control.
If nothing is connected to this pin, the MCU will enter normal operating mode at the rising edge of reset.
If a debug system is connected to the 6-pin standard background debug header, it can hold BKGD low
during the rising edge of reset which forces the MCU to active background mode.
The BKGD/MS pin is used primarily for background debug controller (BDC) communications using a
custom protocol that uses 16 clock cycles of the target MCU’s BDC clock per bit time. The target MCU’s
BDC clock could be as fast as the bus clock rate, so there should never be any significant capacitance
connected to the BKGD/MS pin that could interfere with background serial communications.
Although the BKGD/MS pin is a pseudo open-drain pin, the background debug communication protocol
provides brief, actively driven, high speedup pulses to ensure fast rise times. Small capacitances from
cables and the absolute value of the internal pull-up device play almost no role in determining rise and fall
times on the BKGD/MS pin.
2.2.5
The V
for the ADC module.
2.2.6
The MC9S08DZ60 Series series of MCUs support up to 53 general-purpose I/O pins and 1 input-only pin,
which are shared with on-chip peripheral functions (timers, serial I/O, ADC, MSCAN, etc.).
When a port pin is configured as a general-purpose output or a peripheral uses the port pin as an output,
software can select one of two drive strengths and enable or disable slew rate control. When a port pin is
configured as a general-purpose input or a peripheral uses the port pin as an input, software can enable a
pull-up device. Immediately after reset, all of these pins are configured as high-impedance general-purpose
inputs with internal pull-up devices disabled.
When an on-chip peripheral system is controlling a pin, data direction control bits still determine what is
read from port data registers even though the peripheral module controls the pin direction by controlling
the enable for the pin’s output buffer. For information about controlling these pins as general-purpose I/O
pins, see
32
REFH
Chapter 6, “Parallel Input/Output
Background / Mode Select (BKGD/MS)
ADC Reference Pins (V
General-Purpose I/O and Peripheral Ports
and V
REFL
pins are the voltage reference high and voltage reference low inputs, respectively,
MC9S08DZ60 Series Data Sheet, Rev. 4
REFH
Control.”
, V
REFL
)
Freescale Semiconductor