LPC1759FBD80,551 NXP Semiconductors, LPC1759FBD80,551 Datasheet - Page 436

• Manufacturer Part Number: LPC1759FBD80,551
• Description: IC ARM CORTEX MCU 512K 80-LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC17xxr

Specifications of LPC1759FBD80,551

• Program Memory Type: FLASH
• Program Memory Size: 512KB (512K x 8)
• Package / Case: 80-LQFP
• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 120MHz
• Connectivity: CAN, I²C, IrDA, Microwire, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, Motor Control PWM, POR, PWM, WDT
• Number Of I /o: 52
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 2.4 V ~ 3.6 V
• Data Converters: A/D 6x12b, D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC17
• Core: ARM Cortex M3
• Data Bus Width: 32 bit
• Data Ram Size: 64 KB
• Interface Type: Ethernet, USB, OTG, CAN
• Maximum Clock Frequency: 120 MHz
• Number Of Programmable I/os: 52
• Number Of Timers: 4
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 6 Channel
• On-chip Dac: 10 bit
• Package: 80LQFP
• Device Core: ARM Cortex M3
• Family Name: LPC17xx
• Maximum Speed: 120 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4968; 935290523551

NXP Semiconductors
UM10360
User manual
19.7.2 Address Registers, I2ADR0 to I2ADR3
19.7.3 Address mask registers, I2MASK0 to I2MASK3
19.7.4 Comparator
19.7.5 Shift register, I2DAT
19.7.6 Arbitration and synchronization logic
These registers may be loaded with the 7-bit slave address (7 most significant bits) to
which the I
LSB (GC) is used to enable General Call address (0x00) recognition. When multiple slave
addresses are enabled, the actual address received may be read from the I2DAT register
at the state where the “own slave address” has just been received.
Remark: in the remainder of this chapter, when the phrase “own slave address” is used, it
refers to any of the four configured slave addresses after address masking.
The four mask registers each contain seven active bits (7:1). Any bit in these registers
which is set to ‘1’ will cause an automatic compare on the corresponding bit of the
received address when it is compared to the I2ADRn register associated with that mask
register. In other words, bits in an I2ADRn register which are masked are not taken into
account in determining an address match.
When an address-match interrupt occurs, the processor will have to read the data register
(I2DAT) to determine which received address actually caused the match.
The comparator compares the received 7-bit slave address with any of the four configured
slave addresses in I2ADR0 through I2ADR3 after masking. It also compares the first
received 8-bit byte with the General Call address (0x00). If an a match is found, the
appropriate status bits are set and an interrupt is requested.
This 8-bit register contains a byte of serial data to be transmitted or a byte which has just
been received. Data in I2DAT is always shifted from right to left; the first bit to be
transmitted is the MSB (bit 7) and, after a byte has been received, the first bit of received
data is located at the MSB of I2DAT. While data is being shifted out, data on the bus is
simultaneously being shifted in; I2DAT always contains the last byte present on the bus.
Thus, in the event of lost arbitration, the transition from master transmitter to slave
receiver is made with the correct data in I2DAT.
In the master transmitter mode, the arbitration logic checks that every transmitted logic 1
actually appears as a logic 1 on the I
1 and pulls the SDA line low, arbitration is lost, and the I
from master transmitter to slave receiver. The I
pulses (on SCL) until transmission of the current serial byte is complete.
Arbitration may also be lost in the master receiver mode. Loss of arbitration in this mode
can only occur while the I
Arbitration is lost when another device on the bus pulls this signal low. Since this can
occur only at the end of a serial byte, the I
Figure 91
shows the arbitration procedure.
2
C block will respond when programmed as a slave transmitter or receiver. The
All information provided in this document is subject to legal disclaimers.
Rev. 2 — 19 August 2010
2
C block is returning a “not acknowledge: (logic 1) to the bus.
2
C-bus. If another device on the bus overrules a logic
2
C block generates no further clock pulses.
2
C block will continue to output clock
2
C block immediately changes
Chapter 19: LPC17xx I2C0/1/2
UM10360
© NXP B.V. 2010. All rights reserved.
436 of 840