MC9S08QG4MPAE Freescale Semiconductor, MC9S08QG4MPAE Datasheet - Page 277

• Manufacturer Part Number: MC9S08QG4MPAE
• Description: IC MCU 4K FLASH 8-PDIP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08QG4MPAE

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 4
• Program Memory Size: 4KB (4K x 8)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 8-DIP (0.300", 7.62mm)
• Controller Family/series: HCS08
• No. Of I/o's: 6
• Ram Memory Size: 256Byte
• Cpu Speed: 20MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: S08QG
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: I2C, SCI, SPI
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 12
• Number Of Timers: 1
• Maximum Operating Temperature: + 125 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08QG8E
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

1
2
3
4
5
6
7
Resolution of trimmed DCO output frequency at fixed voltage and
temperature
Total deviation of DCO output from trimmed frequency:
FLL acquisition time
Long term jitter of DCO output clock (averaged over 2-ms interval)
Freescale Semiconductor
When ICS is configured for FEE or FBE mode, input clock source must be divisible using RDIV to within the range of 31.25 kHz
to 39.0625 kHz.
See crystal or resonator manufacturer’s recommendation.
This parameter is characterized and not tested on each device.
Proper PC board layout procedures must be followed to achieve specifications.
TRIM register at default value (0x80) and FTRIM control bit at default value (0x0).
This specification applies to any time the FLL reference source or reference divider is changed, trim value changed or changing
from FLL disabled (FBELP, FBILP) to FLL enabled (FEI, FEE, FBE, FBI). If a crystal/resonator is being used as the reference,
this specification assumes it is already running.
Jitter is the average deviation from the programmed frequency measured over the specified interval at maximum f
Measurements are made with the device powered by filtered supplies and clocked by a stable external clock signal. Noise
injected into the FLL circuitry via V
given interval.
At 8MHz over full voltage and temperature range (M Suffix)
At 8MHz over full voltage and temperature rang (C Suffix)
At 8MHz and 3.6V from 0 to 70°C
Table A-8. XOSC and ICS Specifications (Temperature Range = –40 to 125°C Ambient)
4
4,6
Characteristic
Figure A-7. Typical Crystal or Resonator Circuit
DD
MC9S08QG8 and MC9S08QG4 Data Sheet, Rev. 5
and V
C
1
EXTAL
SS
and variation in crystal oscillator frequency increase the C
Crystal or Resonator
3
(C Suffix)
XOSC
R
F
7
Δf
Symbol
t
Δf
dco_res_t
C
Acquire
dco_t
Jitter
XTAL
R
S
C
Min
—
—
—
—
—
2
Appendix A Electrical Characteristics
–1.5 to ±0.5
–1.0 to ±0.5
±0.1
±0.5
0.02
Typ
Jitter
± 0.2
percentage for a
Max
± 3
± 2
± 1
1.5
0.2
Bus
.
%f
%f
%f
Unit
ms
275
dco
dco
dco