MC9S08QG4MPAE Freescale Semiconductor, MC9S08QG4MPAE Datasheet - Page 57

• Manufacturer Part Number: MC9S08QG4MPAE
• Description: IC MCU 4K FLASH 8-PDIP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08QG4MPAE

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 4
• Program Memory Size: 4KB (4K x 8)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 8-DIP (0.300", 7.62mm)
• Controller Family/series: HCS08
• No. Of I/o's: 6
• Ram Memory Size: 256Byte
• Cpu Speed: 20MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: S08QG
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: I2C, SCI, SPI
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 12
• Number Of Timers: 1
• Maximum Operating Temperature: + 125 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08QG8E
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

4.7.2
During reset, the contents of the nonvolatile location NVOPT are copied from FLASH into FOPT. To
change the value in this register, erase and reprogram the NVOPT location in FLASH memory as usual
and then issue a new MCU reset.
Freescale Semiconductor
SEC0[1:0]
FNORED
Reset
KEYEN
Field
1:0
7
6
W
R
KEYEN
FLASH Options Register (FOPT and NVOPT)
Backdoor Key Mechanism Enable — When this bit is 0, the backdoor key mechanism cannot be used to
disengage security. The backdoor key mechanism is accessible only from user (secured) firmware. BDM
commands cannot be used to write key comparison values that would unlock the backdoor key. For more detailed
information about the backdoor key mechanism, refer to
0 No backdoor key access allowed.
1 If user firmware writes an 8-byte value that matches the nonvolatile backdoor key (NVBACKKEY through
Vector Redirection Disable — When this bit is 1, then vector redirection is disabled.
0 Vector redirection enabled.
1 Vector redirection disabled.
Security State Code — This 2-bit field determines the security state of the MCU as shown in
the MCU is secure, the contents of RAM and FLASH memory cannot be accessed by instructions from any
unsecured source including the background debug interface. SEC01:SEC00 changes to 1:0 after successful
backdoor key entry or a successful blank check of FLASH.
For more detailed information about security, refer to
7
200 kHz
150 kHz
NVBACKKEY+7 in that order), security is temporarily disengaged until the next MCU reset.
20 MHz
10 MHz
8 MHz
4 MHz
2 MHz
1 MHz
f
Bus
= Unimplemented or Reserved
FNORED
(Binary)
PRDIV8
6
1
0
0
0
0
0
0
0
This register is loaded from nonvolatile location NVOPT during reset.
MC9S08QG8 and MC9S08QG4 Data Sheet, Rev. 5
Table 4-8. FOPT Register Field Descriptions
Figure 4-6. FLASH Options Register (FOPT)
Table 4-7. FLASH Clock Divider Settings
(Decimal)
0
5
DIV
12
49
39
19
9
4
0
0
0
4
192.3 kHz
200 kHz
200 kHz
200 kHz
200 kHz
200 kHz
200 kHz
150 kHz
f
FCLK
Description
Section 4.6,
Section 4.6,
3
0
Program/Erase Timing Pulse
(5 μs Min, 6.7 μs Max)
“Security.”
Chapter 4 Memory Map and Register Definition
“Security.”
5.2 μs
6.7 μs
5 μs
5 μs
5 μs
5 μs
5 μs
5 μs
2
0
SEC01
1
Table
4-9. When
SEC00
0
55