MC9S08QG4MPAE Freescale Semiconductor, MC9S08QG4MPAE Datasheet - Page 86

• Manufacturer Part Number: MC9S08QG4MPAE
• Description: IC MCU 4K FLASH 8-PDIP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08QG4MPAE

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 4
• Program Memory Size: 4KB (4K x 8)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 8-DIP (0.300", 7.62mm)
• Controller Family/series: HCS08
• No. Of I/o's: 6
• Ram Memory Size: 256Byte
• Cpu Speed: 20MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: S08QG
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: I2C, SCI, SPI
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 12
• Number Of Timers: 1
• Maximum Operating Temperature: + 125 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08QG8E
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Chapter 6 Parallel Input/Output Control
6.4.4
The pins associated with port B are controlled by the registers in this section. These registers control the
pin pullup, slew rate, and drive strength of the port B pins independent of the parallel I/O register.
6.4.4.1
An internal pullup device can be enabled for each port pin by setting the corresponding bit in the pullup
enable register (PTBPEn). The pullup device is disabled if the pin is configured as an output by the parallel
I/O control logic or any shared peripheral function regardless of the state of the corresponding pullup
enable register bit. The pullup device is also disabled if the pin is controlled by an analog function.
6.4.4.2
Slew rate control can be enabled for each port pin by setting the corresponding bit in the slew rate control
register (PTBSEn). When enabled, slew control limits the rate at which an output can transition in order to
reduce EMC emissions. Slew rate control has no effect on pins which are configured as input.
84
PTBPE[7:0]
PTBSE[7:0]
Reset:
Reset:
Field
Field
7:0
7:0
W
W
R
R
PTBPE7
PTBSE7
Port B Control Registers
Internal Pullup Enable for Port B Bits — Each of these control bits determines if the internal pullup device is
enabled for the associated PTB pin. For port B pins that are configured as outputs, these bits have no effect and
the internal pullup devices are disabled.
0 Internal pullup device disabled for port B bit n.
1 Internal pullup device enabled for port B bit n.
Output Slew Rate Enable for Port B Bits — Each of these control bits determines if the output slew rate control
is enabled for the associated PTB pin. For port B pins that are configured as inputs, these bits have no effect.
0 Output slew rate control disabled for port B bit n.
1 Output slew rate control enabled for port B bit n.
Port B Internal Pullup Enable (PTBPE)
0
Port B Slew Rate Enable (PTBSE)
1
7
7
Figure 6-12. Internal Pullup Enable for Port B Register (PTBPE)
PTBPE6
PTBSE6
Figure 6-14. Slew Rate Enable for Port B Register (PTBSE)
0
1
6
6
Table 6-8. PTBPE Register Field Descriptions
Table 6-9. PTBSE Register Field Descriptions
MC9S08QG8 and MC9S08QG4 Data Sheet, Rev. 5
PTBPE5
PTBSE5
0
1
5
5
PTBPE4
PTBSE4
0
1
4
4
Description
Description
PTBPE3
PTBSE3
3
0
3
1
PTBPE2
PTBSE2
0
1
2
2
PTBPE1
PTBSE1
Freescale Semiconductor
0
1
1
1
PTBPE0
PTBSE0
0
1
0
0