PIC18F86K22-I/PTRSL Microchip Technology, PIC18F86K22-I/PTRSL Datasheet - Page 43

• Manufacturer Part Number: PIC18F86K22-I/PTRSL
• Description: MCU PIC 64K FLASH XLP 80TQFP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F86K22-I/PTRSL

• Core Size: 8-Bit
• Program Memory Size: 64KB (32K x 16)
• Core Processor: PIC
• Speed: 64MHz
• Connectivity: EBI/EMI, I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 69
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 24x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-TFQFP
• Controller Family/series: PIC18
• Eeprom Memory Size: 1024Byte
• Ram Memory Size: 3862Byte
• Cpu Speed: 16MIPS
• No. Of Timers: 11
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

3.2
The OSCCON register (Register 3-1) controls the main
aspects of the device clock’s operation. It selects the
oscillator type to be used, which of the power-managed
modes to invoke and the output frequency of the
INTOSC source. It also provides status on the oscillators.
REGISTER 3-1:
 2010 Microchip Technology Inc.
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6-4
bit 3
Note 1:
IDLEN
R/W-0
2:
3:
4:
5:
6:
Control Registers
The Reset state depends on the state of the IESO Configuration bit (CONFIG1H<7>).
Modifying these bits will cause an immediate clock frequency switch if the internal oscillator is providing
the device clocks.
Source selected by the INTSRC bit (OSCTUNE<7>).
Modifying these bits will cause an immediate clock source switch.
INTSRC = OSCTUNE<7> and MFIOSEL = OSCCON2<0>.
Lowest power option for an internal source.
IDLEN: Idle Enable bit
1 = Device enters an Idle mode when a SLEEP instruction is executed
0 = Device enters Sleep mode when a SLEEP instruction is executed
IRCF<2:0>: Internal Oscillator Frequency Select bits
111 = HF-INTOSC output frequency used (16 MHz)
110 = HF-INTOSC/2 output frequency used (8 MHz, default)
101 = HF-INTOSC/4 output frequency used (4 MHz)
100 = HF-INTOSC/8 output frequency used (2 MHz)
011 = HF-INTOSC/16 output frequency used (1 MHz)
If INTSRC = 0 and MFIOSEL = 0:
010 = HF-INTOSC/32 output frequency used (500 kHz)
001 = HF-INTOSC/64 output frequency used (250 kHz)
000 = LF-INTOSC output frequency used (31.25 kHz)
If INTSRC = 1 and MFIOSEL = 0:
010 = HF-INTOSC/32 output frequency used (500 kHz)
001 = HF-INTOSC/64 output frequency used (250 kHz)
000 = HF-INTOSC/512 output frequency used (31.25 kHz)
If INTSRC = 0 and MFIOSEL = 1:
010 = MF-INTOSC output frequency used (500 kHz)
001 = MF-INTOSC/2 output frequency used (250 kHz)
000 = LF-INTOSC output frequency used (31.25 kHz)
If INTSRC = 1 and MFIOSEL = 1:
010 = MF-INTOSC output frequency used (500 kHz)
001 = MF-INTOSC/2 output frequency used (250 kHz)
000 = MF-INTOSC/16 output frequency used (31.25 kHz)
OSTS: Oscillator Start-up Timer Time-out Status bit
1 = Oscillator Start-up Timer (OST) time-out has expired; primary oscillator is running, as defined by
0 = Oscillator Start-up Timer (OST) time-out is running; primary oscillator is not ready – device is
IRCF2
R/W-1
FOSC<3:0>
running from internal oscillator (HF-INTOSC, MF-INTOSC or LF-INTOSC)
OSCCON: OSCILLATOR CONTROL REGISTER
(2)
W = Writable bit
‘1’ = Bit is set
IRCF1
R/W-1
(2)
IRCF0
R/W-0
(3,5)
(3,5)
(3,5)
(3,5)
Preliminary
(2)
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
PIC18F87K22 FAMILY
OSTS
The OSCTUNE register (Register 3-3) controls the
tuning and operation of the internal oscillator block. It also
implements the PLLEN bit which controls the operation of
the Phase Locked Loop (PLL) (see Section 3.5.3 “PLL
Frequency Multiplier”).
R
(1)
(1)
(2)
(6)
HFIOFS
(1)
R-0
x = Bit is unknown
SCS1
R/W-0
(4)
DS39960B-page 43
SCS0
R/W-0
(4)
bit 0