PIC18F86K22-I/PTRSL Microchip Technology, PIC18F86K22-I/PTRSL Datasheet - Page 71

• Manufacturer Part Number: PIC18F86K22-I/PTRSL
• Description: MCU PIC 64K FLASH XLP 80TQFP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F86K22-I/PTRSL

• Core Size: 8-Bit
• Program Memory Size: 64KB (32K x 16)
• Core Processor: PIC
• Speed: 64MHz
• Connectivity: EBI/EMI, I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 69
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 24x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-TFQFP
• Controller Family/series: PIC18
• Eeprom Memory Size: 1024Byte
• Ram Memory Size: 3862Byte
• Cpu Speed: 16MIPS
• No. Of Timers: 11
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

5.0
The PIC18F87K22 family of devices differentiates
between various kinds of Reset:
a)
b)
c)
d)
e)
f)
g)
h)
i)
This section discusses Resets generated by MCLR,
POR and BOR, and covers the operation of the various
start-up timers. Stack Reset events are covered in
Section 6.1.3.4 “Stack Full and Underflow Resets”.
WDT Resets are covered in Section 28.2 “Watchdog
Timer (WDT)”.
A simplified block diagram of the on-chip Reset circuit
is shown in Figure 5-1.
FIGURE 5-1:
 2010 Microchip Technology Inc.
MCLR
Power-on Reset (POR)
MCLR Reset during normal operation
MCLR Reset during power-managed modes
Watchdog Timer (WDT) Reset (during
execution)
Configuration Mismatch (CM) Reset
Brown-out Reset (BOR)
RESET Instruction
Stack Full Reset
Stack Underflow Reset
V
DD
RESET
Configuration Word Mismatch
PWRT
Pointer
Stack
LF-INTOSC
( )_IDLE
V
Brown-out
32 s
Time-out
DD
Detect
WDT
Reset
Sleep
Rise
External Reset
SIMPLIFIED BLOCK DIAGRAM OF ON-CHIP RESET CIRCUIT
Stack Full/Underflow Reset
RESET Instruction
POR Pulse
PWRT
11-Bit Ripple Counter
66 ms
Preliminary
PIC18F87K22 FAMILY
5.1
Device Reset events are tracked through the RCON
register (Register 5-1). The lower five bits of the
register indicate that a specific Reset event has
occurred. In most cases, these bits can only be set by
the event and must be cleared by the application after
the event.
The state of these flag bits, taken together, can be read
to indicate the type of Reset that just occurred. This is
described in more detail in Section 5.7 “Reset State
of Registers”.
The RCON register also has a control bit for setting
interrupt priority (IPEN). Interrupt priority is discussed
in Section 11.0 “Interrupts”.
RCON Register
S
R
Q
DS39960B-page 71
Chip_Reset