PIC18LF27J53-I/ML Microchip Technology, PIC18LF27J53-I/ML Datasheet - Page 282

• Manufacturer Part Number: PIC18LF27J53-I/ML
• Description: IC PIC MCU 128KB FLASH 28QFN
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18LF27J53-I/ML

• Core Size: 8-Bit
• Program Memory Size: 128KB (64K x 16)
• Core Processor: PIC
• Speed: 48MHz
• Connectivity: I²C, LIN, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Type: FLASH
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 2.75 V
• Data Converters: A/D 10x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Controller Family/series: PIC18
• Cpu Speed: 48MHz
• Digital Ic Case Style: QFN
• Supply Voltage Range: 1.8V To 3.6V
• Embedded Interface Type: I2C, SPI, USART
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC18F47J53 FAMILY
FIGURE 19-11:
19.4.3
When any PWM mode is used, the application
hardware must use the proper external pull-up and/or
pull-down resistors on the PWM output pins.
The CCPxM<1:0> bits of the CCPxCON register allow
the user to choose whether the PWM output signals are
active-high or active-low for each pair of PWM output
pins (PxA/PxC and PxB/PxD). The PWM output
polarities must be selected before the PWM pin output
drivers are enabled. Changing the polarity configura-
tion while the PWM pin output drivers are enabled is
not recommended, since it may result in damage to the
application circuits.
The PxA, PxB, PxC and PxD output latches may not be
in the proper states when the PWM module is
initialized. Enabling the PWM pin output drivers at the
same time as the Enhanced PWM modes may cause
damage to the application circuit. The Enhanced PWM
modes must be enabled in the proper Output mode and
complete a full PWM cycle before enabling the PWM
DS39964B-page 282
Note:
Shoot-Through Current
Note 1: All signals are shown as active-high.
External Switch C
External Switch D
2: T
3: T
START-UP CONSIDERATIONS
When the microcontroller is released from
Reset, all of the I/O pins are in the
high-impedance
circuits must keep the power switch
devices in the OFF state until the micro-
controller drives the I/O pins with the
proper signal levels or activates the PWM
output(s).
ON
OFF
Potential
is the turn-on delay of power switch, QC, and its driver.
is the turn-off delay of power switch, QD, and its driver.
PxA
PxB
PxC
PxD
EXAMPLE OF PWM DIRECTION CHANGE AT NEAR 100% DUTY CYCLE
state.
The
Forward Period
external
PW
Preliminary
pin output drivers. The completion of a full PWM cycle
is indicated by the TMR2IF or TMR4IF bit of the PIR1
or PIR3 register being set as the second PWM period
begins.
19.4.4
The PWM mode supports an Auto-Shutdown mode that
will disable the PWM outputs when an external
shutdown event occurs. Auto-Shutdown mode places
the PWM output pins into a predetermined state. This
mode is used to help prevent the PWM from damaging
the application.
The auto-shutdown sources are selected using the
ECCPxAS<2:0> bits (ECCPxAS<6:4>). A shutdown
event may be generated by:
• A logic ‘0’ on the pin that is assigned to the FLT0
• Comparator C1
• Comparator C2
• Setting the ECCPxASE bit in firmware
A shutdown condition is indicated by the ECCPxASE
(Auto-Shutdown Event Status) bit (ECCPxAS<7>). If
the bit is a ‘0’, the PWM pins are operating normally. If
the bit is a ‘1’, the PWM outputs are in the shutdown
state.
input function
t1
ENHANCED PWM
AUTO-SHUTDOWN MODE
T
ON
Reverse Period
T
T = T
OFF
OFF
PW
 2010 Microchip Technology Inc.
– T
ON