ATmega168P Atmel Corporation, ATmega168P Datasheet - Page 179

no-image

ATmega168P

Manufacturer Part Number
ATmega168P
Description
Manufacturer
Atmel Corporation
Datasheets

Specifications of ATmega168P

Flash (kbytes)
16 Kbytes
Pin Count
32
Max. Operating Frequency
20 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
23
Ext Interrupts
24
Usb Speed
No
Usb Interface
No
Spi
2
Twi (i2c)
1
Uart
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
1
Eeprom (bytes)
512
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
Yes
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8 to 5.5
Operating Voltage (vcc)
1.8 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
3
Output Compare Channels
6
Input Capture Channels
1
Pwm Channels
6
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Company:
Bonase Electronics (HK) Co., Limited Bonase Electronics (HK) Co., Limited
Part Number:
ATmega168PA-15AZ
Manufacturer:
VAC
Quantity:
120
Price:
Company:
CHD Technology Co.,Limited CHD Technology Co.,Limited
Part Number:
ATmega168PA-AU
Manufacturer:
MICROCHIP
Quantity:
250
Price:
Company:
Bonase Electronics (HK) Co., Limited Bonase Electronics (HK) Co., Limited
Part Number:
ATmega168PA-MU
Manufacturer:
ATMEL
Quantity:
4 000
Price:
Company:
Bonase Electronics (HK) Co., Limited Bonase Electronics (HK) Co., Limited
Part Number:
ATmega168PA-PU
Manufacturer:
TI
Quantity:
1 240
Price:
Company:
Bonase Electronics (HK) Co., Limited Bonase Electronics (HK) Co., Limited
Part Number:
ATmega168PB-AU
Manufacturer:
ATMEL
Quantity:
1 000
Price:
20.4.1
8025M–AVR–6/11
Parity Bit Calculation
A frame starts with the start bit followed by the least significant data bit. Then the next data bits,
up to a total of nine, are succeeding, ending with the most significant bit. If enabled, the parity bit
is inserted after the data bits, before the stop bits. When a complete frame is transmitted, it can
be directly followed by a new frame, or the communication line can be set to an idle (high) state.
Figure 20-4
optional.
Figure 20-4. Frame Formats
must be
The frame format used by the USART is set by the UCSZn2:0, UPMn1:0 and USBSn bits in
UCSRnB and UCSRnC. The Receiver and Transmitter use the same setting. Note that changing
the setting of any of these bits will corrupt all ongoing communication for both the Receiver and
Transmitter.
The USART Character SiZe (UCSZn2:0) bits select the number of data bits in the frame. The
USART Parity mode (UPMn1:0) bits enable and set the type of parity bit. The selection between
one or two stop bits is done by the USART Stop Bit Select (USBSn) bit. The Receiver ignores
the second stop bit. An FE (Frame Error) will therefore only be detected in the cases where the
first stop bit is zero.
The parity bit is calculated by doing an exclusive-or of all the data bits. If odd parity is used, the
result of the exclusive or is inverted. The relation between the parity bit and data bits is as
follows:
If used, the parity bit is located between the last data bit and first stop bit of a serial frame.
St
(n)
P
Sp
IDLE
P
P
d
even
odd
n
illustrates the possible combinations of the frame formats. Bits inside brackets are
(IDLE)
St
Start bit, always low.
Data bits (0 to 8).
Parity bit. Can be odd or even.
Stop bit, always high.
No transfers on the communication line (RxDn or TxDn). An IDLE line
high.
Parity bit using even parity
Parity bit using odd parity
Data bit n of the character
P
0
P
even
odd
1
=
=
d
d
2
n 1
n 1
3
4
FRAME
[5]
d
d
3
3
[6]
d
d
2
2
ATmega48P/88P/168P
[7]
d
d
1
1
[8]
d
d
0
0
[P]
0
1
Sp1 [Sp2]
(St / IDLE)
179

Related parts for ATmega168P