ATmega168P Atmel Corporation, ATmega168P Datasheet - Page 35

no-image

ATmega168P

Manufacturer Part Number
ATmega168P
Description
Manufacturer
Atmel Corporation
Datasheets

Specifications of ATmega168P

Flash (kbytes)
16 Kbytes
Pin Count
32
Max. Operating Frequency
20 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
23
Ext Interrupts
24
Usb Speed
No
Usb Interface
No
Spi
2
Twi (i2c)
1
Uart
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
1
Eeprom (bytes)
512
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
Yes
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8 to 5.5
Operating Voltage (vcc)
1.8 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
3
Output Compare Channels
6
Input Capture Channels
1
Pwm Channels
6
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATmega168P-20AN
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega168P-20ANR
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega168P-20AU
Manufacturer:
ATMEL
Quantity:
1 250
Part Number:
ATmega168P-20AU
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega168P-20AUR
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega168P-20MU
Manufacturer:
ATMEL
Quantity:
12 000
Part Number:
ATmega168PA-15AZ
Manufacturer:
VAC
Quantity:
120
Part Number:
ATmega168PA-15AZ
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega168PA-15MZ
Manufacturer:
TOSHIBA
Quantity:
1 000
Part Number:
ATmega168PA-AU
Manufacturer:
Atmel
Quantity:
2 902
Company:
Part Number:
ATmega168PA-AU
Manufacturer:
MICROCHIP
Quantity:
5 502
Company:
Part Number:
ATmega168PA-AU
Manufacturer:
ATMEL
Quantity:
2 300
Company:
Part Number:
ATmega168PA-AUR
Manufacturer:
ATMEL
Quantity:
32
Company:
Part Number:
ATmega168PA-MMH
Manufacturer:
ATMEL
Quantity:
350
9.7
9.8
8025M–AVR–6/11
128 kHz Internal Oscillator
External Clock
The 128 kHz internal Oscillator is a low power Oscillator providing a clock of 128 kHz. The fre-
quency is nominal at 3V and 25°C. This clock may be select as the system clock by
programming the CKSEL Fuses to “11” as shown in
Table 9-13.
Note:
When this clock source is selected, start-up times are determined by the SUT Fuses as shown in
Table
Table 9-14.
Note:
To drive the device from an external clock source, XTAL1 should be driven as shown in
9-4 on page
to “0000” (see
Table 9-15.
Figure 9-4.
When this clock source is selected, start-up times are determined by the SUT Fuses as shown in
Table
BOD enabled
Fast rising power
Slowly rising power
Power Conditions
9-14.
9-16.
1. Note that the 128 kHz oscillator is a very low power clock source, and is not designed for a
1. If the RSTDISBL fuse is programmed, this start-up time will be increased to
high accuracy.
14CK + 4.1 ms to ensure programming mode can be entered.
35. To run the device on an external clock, the CKSEL Fuses must be programmed
128 kHz Internal Oscillator Operating Modes
Start-up Times for the 128 kHz Internal Oscillator
Table
Crystal Oscillator Clock Frequency
External Clock Drive Configuration
Nominal Frequency
9-15).
Frequency
0 - 20 MHz
EXTERNAL
128 kHz
SIGNAL
CLOCK
Start-up Time from Power-
down and Power-save
NC
(1)
Reserved
6 CK
6 CK
6 CK
Table
ATmega48P/88P/168P
XTAL2
XTAL1
GND
9-13.
Additional Delay from
14CK + 64 ms
14CK + 4 ms
14CK
Reset
CKSEL[3:0]
CKSEL[3:0]
(1)
0011
0000
SUT[1:0]
Figure
00
01
10
11
35

Related parts for ATmega168P