ATmega168P Atmel Corporation, ATmega168P Datasheet - Page 30

no-image

ATmega168P

Manufacturer Part Number
ATmega168P
Description
Manufacturer
Atmel Corporation
Datasheets

Specifications of ATmega168P

Flash (kbytes)
16 Kbytes
Pin Count
32
Max. Operating Frequency
20 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
23
Ext Interrupts
24
Usb Speed
No
Usb Interface
No
Spi
2
Twi (i2c)
1
Uart
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
1
Eeprom (bytes)
512
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
Yes
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8 to 5.5
Operating Voltage (vcc)
1.8 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
3
Output Compare Channels
6
Input Capture Channels
1
Pwm Channels
6
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATmega168P-20AN
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega168P-20ANR
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega168P-20AU
Manufacturer:
ATMEL
Quantity:
1 250
Part Number:
ATmega168P-20AU
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega168P-20AU
Manufacturer:
ATMEL
Quantity:
1 011
Part Number:
ATmega168P-20AUR
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega168P-20MU
Manufacturer:
ATMEL
Quantity:
12 000
Part Number:
ATmega168PA
Manufacturer:
ATMEL
Quantity:
2 650
Part Number:
ATmega168PA-15AZ
Manufacturer:
VAC
Quantity:
120
Part Number:
ATmega168PA-15AZ
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega168PA-15MZ
Manufacturer:
TOSHIBA
Quantity:
1 000
Part Number:
ATmega168PA-AU
Manufacturer:
Atmel
Quantity:
2 902
Company:
Part Number:
ATmega168PA-AU
Manufacturer:
MICROCHIP
Quantity:
5 502
Company:
Part Number:
ATmega168PA-AU
Manufacturer:
ATMEL
Quantity:
2 300
Part Number:
ATmega168PA-AU
Manufacturer:
ATMEL
Quantity:
200
Company:
Part Number:
ATmega168PA-AUR
Manufacturer:
ATMEL
Quantity:
32
30
ATmega48P/88P/168P
Figure 9-2.
The Low Power Oscillator can operate in three different modes, each optimized for a specific fre-
quency range. The operating mode is selected by the fuses CKSEL[3:1] as shown in
on page
Table 9-3.
Notes:
The CKSEL0 Fuse together with the SUT[1:0] Fuses select the start-up times as shown in
9-4.
Table 9-4.
Oscillator Source /
Power Conditions
Ceramic resonator, fast
rising power
Ceramic resonator, slowly
rising power
Ceramic resonator, BOD
enabled
Ceramic resonator, fast
rising power
Ceramic resonator, slowly
rising power
Frequency Range
1. This is the recommended CKSEL settings for the different frequency ranges.
2. This option should not be used with crystals, only with ceramic resonators.
3. If 8 MHz frequency exceeds the specification of the device (depends on V
30.
8.0 - 16.0
0.4 - 0.9
0.9 - 3.0
3.0 - 8.0
(MHz)
Fuse can be programmed in order to divide the internal frequency by 8. It must be ensured
that the resulting divided clock meets the frequency specification of the device.
Crystal Oscillator Connections
Low Power Crystal Oscillator Operating Modes
Start-up Times for the Low Power Crystal Oscillator Clock Selection
(1)
Start-up Time from
Power-down and
C2
C1
Power-save
258 CK
258 CK
1K CK
1K CK
1K CK
Capacitors C1 and C2 (pF)
Recommended Range for
12 - 22
12 - 22
12 - 22
XTAL2 (TOSC2)
XTAL1 (TOSC1)
GND
Additional Delay
14CK + 4.1 ms
14CK + 4.1 ms
14CK + 65 ms
14CK + 65 ms
(V
from Reset
CC
14CK
= 5.0V)
(3)
(2)
(1)
(2)
(1)
(2)
CKSEL0
CC
0
0
0
0
1
CKSEL[3:1]
), the CKDIV8
100
101
110
111
8025M–AVR–6/11
(2)
Table 9-3
SUT[1:0]
00
01
10
11
00
Table

Related parts for ATmega168P