ATtiny167 Atmel Corporation, ATtiny167 Datasheet - Page 167

• Manufacturer Part Number: ATtiny167
• Manufacturer: Atmel Corporation

Specifications of ATtiny167

• Flash (kbytes): 16 Kbytes
• Pin Count: 20
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 8
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 16
• Ext Interrupts: 16
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Lin: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 3
• Input Capture Channels: 1
• Pwm Channels: 9
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

15.4.5
15.4.6
15.4.6.1
8265B–AVR–09/10
Enable / Disable
LIN Commands
Rx Header / LIN Abort Function
Table 15-1.
Setting the LENA bit in LINCR register enables the LIN/UART controller. To disable the
LIN/UART controller, LENA bit must be written to 0. No wait states are implemented, so, the
disable command is taken into account immediately.
Clearing the LCMD[2] bit in LINCR register enables LIN commands.
As shown in
register are available (c.f.
This function (or state) is mainly the withdrawal mode of the controller.
When the controller has to execute a master task, this state is the start point before enabling a
Tx Header command.
When the controller has only to execute slave tasks, LIN header detection/acquisition is
enabled as background function. At the end of such an acquisition (Rx Header function), auto-
matically the appropriate flags are set, and in LIN 1.3, the LINDLR register is set with the
uncoded length value.
This state is also the start point before enabling the Tx or the Rx Response command.
A running function (i.e. Tx Header, Tx or Rx Response ) can be aborted by clearing LCMD[1:0]
bits in LINCR register
LABORT - in LINERR register will be set to inform the other software tasks. No wait states are
implemented, so, the abort command is taken into account immediately.
Rx Header function is responsible for:
LENA
• The BREAK field detection,
• The hardware re-synchronization analyzing the SYNCH field,
• The reception of the PROTECTED IDENTIFIER field, the parity control and the update of
• The starting of the Frame_Time_Out,
• The checking of the LIN communication integrity.
the LINDLR register in case of LIN 1.3,
0
1
LCMD[2]
Table 15-1 on page
x
0
1
LIN/UART Command List
LCMD[1]
(See ”Break-in-data” on page
x
0
1
0
1
0
1
Figure 15-5 on page
LCMD[0]
167, four functions controlled by the LCMD[1:0] bits of LINCR
x
0
1
0
1
0
0
1
1
Rx Header - LIN Abort
Disable peripheral
166).
Rx Response
Tx Response
Byte transfer
Command
Full duplex
Tx Header
Rx Byte
Tx Byte
177.). In this case, an abort flag -
(LINDLR: read only register)
LCMD[2:0]=000 after Rx
LCMD[2:0]=000 after Tx
LCMD[2:0]=000 after Tx
no CRC, no Time out
LTXDL=LRXDL=0
LIN Withdrawal
Comment
167