ATtiny167 Atmel Corporation, ATtiny167 Datasheet - Page 53

• Manufacturer Part Number: ATtiny167
• Manufacturer: Atmel Corporation

Specifications of ATtiny167

• Flash (kbytes): 16 Kbytes
• Pin Count: 20
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 8
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 16
• Ext Interrupts: 16
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Lin: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 3
• Input Capture Channels: 1
• Pwm Channels: 9
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

6.2
6.2.1
6.3
6.3.1
8265B–AVR–09/10
Internal Voltage Reference
Watchdog Timer
Voltage Reference Enable Signals and Start-up Time
Watchdog Timer Behavior
• Bit 1 – EXTRF: External Reset Flag
This bit is set if an External Reset occurs. The bit is reset by a Power-on Reset, or by writing a
logic zero to the flag.
• Bit 0 – PORF: Power-on Reset Flag
This bit is set if a Power-on Reset occurs. The bit is reset only by writing a logic zero to the
flag.
To make use of the Reset Flags to identify a reset condition, the user should read and then
Reset the MCUSR as early as possible in the program. If the register is cleared before another
reset occurs, the source of the reset can be found by examining the Reset Flags.
ATtiny87/167 features an internal bandgap reference. This reference is used for Brown-out
Detection, and it can be used as an input to the Analog Comparator or the ADC.
The voltage reference has a start-up time that may influence the way it should be used. The
start-up time is given in
turned on. The reference is on during the following situations:
Thus, when the BOD is not enabled, after setting the ACIRS bit or enabling the ADC, the user
must always allow the reference to start up before the output from the Analog Comparator or
ADC is used. To reduce power consumption in Power-down mode or in Power-save, the user
can avoid the three conditions above to ensure that the reference is turned off before entering
in these power reduction modes.
ATtiny87/167 has an Enhanced Watchdog Timer (WDT). The main features are:
•
•
•
•
The Watchdog Timer (WDT) is a timer counting cycles of a separate on-chip 128 KHz
oscillator.
1. When the BOD is enabled (by programming the BODLEVEL[2:0] Fuses).
2. When the bandgap reference is connected to the Analog Comparator (by setting the
3. When the ADC is enabled.
Clocked from separate On-chip Oscillator
4 Operating modes
Selectable Time-out period from 16ms to 8s
Possible Hardware fuse Watchdog always on (WDTON) for fail-safe mode
– Interrupt
– System Reset
– Interrupt and System Reset
– Clock Monitoring
ACIRS bit in ACSR).
Table 22-7 on page
247. To save power, the reference is not always
53