ATtiny167 Atmel Corporation, ATtiny167 Datasheet - Page 244

• Manufacturer Part Number: ATtiny167
• Manufacturer: Atmel Corporation

Specifications of ATtiny167

• Flash (kbytes): 16 Kbytes
• Pin Count: 20
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 8
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 16
• Ext Interrupts: 16
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Lin: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 3
• Input Capture Channels: 1
• Pwm Channels: 9
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

T
Notes:
244
A
Symbol
R
R
I
V
I
t
CC
ACLK
ACID
= -40°C to +85°C, V
ACIO
RST
pu
1. “Typ.", typical values at 25°C. Maximum values are characterized values and not test limits in production.
2. "Max.” means the highest value where the pin is guaranteed to be read as low.
3. “Min.” means the lowest value where the pin is guaranteed to be read as high.
4. Although each I/O port can sink more than the test conditions (10 mA at V
5. Although each I/O port can source more than the test conditions (10 mA at V
6. Values are with external clock using methods described in
7. BOD Disabled.
ATtiny87/ATtiny167
ditions (non-transient), the following must be observed:
- The sum of all IOL, for all ports, should not exceed 120 mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
conditions (non-transient), the following must be observed:
- The sum of all IOH, for all ports, should not exceed 120 mA.
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition.
is enabled (PRR = 0xFF) and there is no I/O drive.
Parameter
Reset Pull-up Resistor
I/O Pin Pull-up Resistor
Power Supply Current
Active Mode
(external clock)
Power Supply Current
Idle Mode
(external clock)
Power Supply Current
Power-down Mode
Analog Comparator
Input Offset Voltage
Analog Comparator
Input Leakage Current
Analog Comparator
Propagation Delay
Common Mode V
CC
= 1.8V to 5.5V (unless otherwise noted) (Continued)
CC
/2
(6)
(6)
(7)
Condition
8 MHz, V
4 MHz, V
1 MHz, V
8 MHz, V
4 MHz, V
1 MHz, V
WDT enabled, V
WDT disabled, V
V
V
V
V
V
V
CC
in
CC
in
CC
CC
= V
= V
= 5V
= 5V
= 2.7V
= 5.0V
CC
CC
/2
/2
CC
CC
CC
CC
CC
CC
= 5V
= 3V
= 2V
= 5V
= 3V
= 2V
CC
CC
= 3V
= 3V
“Minimizing Power Consumption” on page
Min.
-10
-50
30
20
CC
= 5V, 5 mA at V
CC
Typ.
= 5V, 5 mA at V
0.05
0.15
170
180
5.5
1.8
0.3
1.8
0.5
10
5
(1)
CC
= 3V) under steady state con-
CC
Max.
7.0
2.5
0.6
2.5
0.8
0.2
60
50
10
40
50
4
= 3V) under steady state
45. Power Reduction
8265B–AVR–09/10
Units
mA
mA
mA
mA
mA
mA
mV
kΩ
kΩ
µA
µA
nA
ns
ns