MC9S12E256VPVE Freescale Semiconductor, MC9S12E256VPVE Datasheet - Page 158

• Manufacturer Part Number: MC9S12E256VPVE
• Description: IC MCU 256K FLASH 25MHZ 112-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12E256VPVE

• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 25MHz
• Connectivity: EBI/EMI, I²C, SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 91
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 2.35 V ~ 2.75 V
• Data Converters: A/D 16x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 112-LQFP
• Processor Series: S12E
• Core: HCS12
• Data Bus Width: 16 bit
• Data Ram Size: 16 KB
• Interface Type: I2C/SCI/SPI
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 92
• Number Of Timers: 12
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16-ch x 10-bit
• On-chip Dac: 2-ch x 8-bit
• For Use With: M68EVB912E128 - BOARD EVAL FOR MC9S12E128/64
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Chapter 3 Port Integration Module (PIM9E256V1)
3.4
Each pin associated with ports AD, M, P, Q, S, T and U can act as general-purpose I/O. In addition the pin
can act as an output from a peripheral module or an input to a peripheral module.
A set of configuration registers is common to all ports. All registers can be written at any time, however a
specific configuration might not become active.
3.4.1
The I/O Register holds the value driven out to the pin if the port is used as a general-purpose I/O. Writing
to the I/O Register only has an effect on the pin if the port is used as general-purpose output.
When reading the I/O Register, the value of each pin is returned if the corresponding Data Direction
Register bit is set to 0 (pin configured as input). If the data direction register bits is set to 1, the content of
the I/O Register bit is returned. This is independent of any other configuration
Due to internal synchronization circuits, it can take up to 2 bus cycles until the correct value is read on the
I/O Register when changing the data direction register.
3.4.2
The Input Register is a read-only register and generally returns the value of the pin
be used to detect overload or short circuit conditions.
Due to internal synchronization circuits, it can take up to 2 bus cycles until the correct value is read on the
Input Register when changing the Data Direction Register.
3.4.3
The Data Direction Register defines whether the pin is used as an input or an output. A Data Direction
Register bit set to 0 configures the pin as an input. A Data Direction Register bit set to 0 configures the pin
as an output. If a peripheral module controls the pin the contents of the data direction register is ignored
(Figure
158
Example: Selecting a pull-up resistor. This resistor does not become active while the port is used
as a push-pull output.
3-49).
Functional Description
I/O Register
Input Register
Data Direction Register
MC9S12E256 Data Sheet, Rev. 1.08
(Figure
(Figure
Freescale Semiconductor
3-49).
3-49). It can