UPD78F1506GF-GAT-AX Renesas Electronics America, UPD78F1506GF-GAT-AX Datasheet - Page 358

• Manufacturer Part Number: UPD78F1506GF-GAT-AX
• Description: MCU 16BIT 78K0R/LX3 128-LQFP
• Manufacturer: Renesas Electronics America
• Series: 78K0R/Lx3r

Specifications of UPD78F1506GF-GAT-AX

• Core Processor: 78K/0R
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: 3-Wire SIO, I²C, LIN, UART/USART
• Peripherals: DMA, LCD, LVD, POR, PWM, WDT
• Number Of I /o: 78
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 12x12b, D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

78K0R/Lx3
R01UH0004EJ0401 Rev.4.01
Jul 2, 2010
Caution If writing is performed to the RTCC1 register with a 1-bit manipulation instruction, the RIFG and
Remark Fixed-cycle interrupts and alarm match interrupts use the same interrupt source (INTRTC). When using
This flag indicates the status of generation of the constant-period interrupt. When the constant-period interrupt is
generated, it is set to “1”.
This flag is cleared when “0” is written to it. Writing “1” to it is invalid.
This status flag indicates whether the setting of RWAIT is valid.
Before reading or writing the counter value, confirm that the value of this flag is 1.
This bit controls the operation of the counter.
Be sure to write “1” to it to read or write the counter value.
Because RSUBC continues operation, complete reading or writing of it in 1 second, and clear this bit back to 0.
When RWAIT = 1, it takes up to 1 clock (32.768 kHz) until the counter value can be read or written.
If RSUBC overflows when RWAIT = 1, it counts up after RWAIT = 0. If the second count register is written,
however, it does not count up because RSUBC is cleared.
RWAIT
RWST
RIFG
WAFG flags may be cleared. Therefore, to perform writing to the RIFG and WAFG flags, be sure
to use an 8-bit manipulation instruction. At this time, set 1 to the RIFG and WAFG flags to
invalidate writing and not to clear the RIFG and WAFG flags during writing. When the value may
be rewritten because the RIFG and WAFG flags are not being used, the RTCC1 register may be
written by using a 1-bit manipulation instruction.
these two types of interrupts at the same time, which interrupt occurred can be judged by checking the
fixed-cycle interrupt status flag (RIFG) and the alarm detection status flag (WAFG) upon INTRTC
occurrence.
0
1
0
1
0
1
Figure 7-4. Format of Real-Time Counter Control Register 1 (RTCC1) (2/2)
Constant-period interrupt is not generated.
Constant-period interrupt is generated.
Counter is operating.
Mode to read or write counter value
Sets counter operation.
Stops SEC to YEAR counters. Mode to read or write counter value
Constant-period interrupt status flag
Wait status flag of real-time counter
Wait control of real-time counter
CHAPTER 7 REAL-TIME COUNTER
358