UPD78F1506GF-GAT-AX Renesas Electronics America, UPD78F1506GF-GAT-AX Datasheet - Page 56

• Manufacturer Part Number: UPD78F1506GF-GAT-AX
• Description: MCU 16BIT 78K0R/LX3 128-LQFP
• Manufacturer: Renesas Electronics America
• Series: 78K0R/Lx3r

Specifications of UPD78F1506GF-GAT-AX

• Core Processor: 78K/0R
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: 3-Wire SIO, I²C, LIN, UART/USART
• Peripherals: DMA, LCD, LVD, POR, PWM, WDT
• Number Of I /o: 78
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 12x12b, D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

78K0R/Lx3
2.2.5 P40, P41
and clock output for a debugger.
(1) Port mode
(2) Control mode
R01UH0004EJ0401 Rev.4.01
Jul 2, 2010
Cautions 1.
P40 and P41 function as an I/O port. These pins also function as data I/O for a flash memory programmer/debugger
The following operation modes can be specified in 1-bit units.
P40/TOOL0
P41/TOOL1
P40 and P41 function as an I/O port. P40 and P41 can be set to input or output port in 1-bit units using port mode
register 4 (PM4). Use of an on-chip pull-up resistor can be specified by pull-up resistor option register 4 (PU4).
Be sure to connect an external pull-up resistor to P40 when on-chip debugging is enabled (by using an option byte).
P40 and P41 function as data I/O for a flash memory programmer/debugger and clock output for a debugger.
(a) TOOL0
This is a data I/O pin for a flash memory programmer/debugger.
Be sure to pull up this pin externally when on-chip debugging is enabled (pulling it down is prohibited).
2.
3.
4.
To use P30/TO00/TI03/RTC1HZ/INTP1 as a general-purpose port, set bit 5 (RCLOE1) of real-time
counter control register 0 (RTCC0), bit 0 (TO00) of timer output register 0 (TO0) and bit 0 (TOE00)
of timer output enable register 0 (TOE0) to “0”, which is the same as their default status setting.
To use P31/TO03/TI00/RTCDIV/RTCCL/PCLBUZ1/INTP2 as a general-purpose port, set bit 4
(RCLOE0) of real-time counter control register 0 (RTCC0), bit 6 (RCLOE2) of real-time counter
control register 2 (RTCC2), bit 3 (TO03) of timer output register 0 (TO0), bit 3 (TOE03) of timer
output enable register 0 (TOE0) and bit 7 of clock output select register 1 (CKS1) to “0”, which is
the same as their default status setting.
To use P32/TO01/TI01/INTP5/PCLBUZ0 as a general-purpose port, set bit 1 (TO01) of timer output
register 0 (TO0), bit 1 (TOE01) of timer output enable register 0 (TOE0) and bit 7 of clock output
select register 0 (CKS0) to “0”, which is the same as their default status setting.
To use P33/TO07/TI07/INTP3 and P34/TO06/TI06/INTP8 as a general-purpose port, set bit 7, 6
(TO07, TO06) of timer output register 0 (TO0), and bit 7, 6 (TOE07, TOE06) of timer output enable
register 0 (TOE0) to “0”, which is the same as their default status setting.
(80 pins:
78F1501A, 78F1502A)
78K0R/LF3
μ
PD78F1500A,
(100 pins:
78F1504A, 78F1505A)
78K0R/LG3
μ
PD78F1503A,
√
√
CHAPTER 2 PIN FUNCTIONS
(128 pins:
78F1507A, 78F1508A)
78K0R/LH3
μ
PD78F1506A,
56