ATmega1284PR231 Atmel Corporation, ATmega1284PR231 Datasheet - Page 5
ATmega1284PR231
Manufacturer Part Number
ATmega1284PR231
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT86RF231.pdf
(198 pages)
2.ATMEGA1284PR231.pdf
(380 pages)
3.ATMEGA1284PR231.pdf
(20 pages)
Specifications of ATmega1284PR231
Flash (kbytes)
128 Kbytes
Max. Operating Frequency
20 MHz
Max I/o Pins
32
Spi
3
Twi (i2c)
1
Uart
2
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Crypto Engine
AES
Sram (kbytes)
16
Eeprom (bytes)
4096
Operating Voltage (vcc)
1.8 to 3.6
Timers
3
Frequency Band
2.4 GHz
Max Data Rate (mb/s)
2
Antenna Diversity
Yes
External Pa Control
Yes
Power Output (dbm)
3
Receiver Sensitivity (dbm)
-101
Receive Current Consumption (ma)
13.2
Transmit Current Consumption (ma)
14.4
Link Budget (dbm)
104
- Current page: 5 of 198
- Download datasheet (5Mb)
1.2
1.2.1
1.2.2
8111C–MCU Wireless–09/09
Analog and RF Pins
Supply and Ground Pins
RF Pins
EVDD, DEVDD
EVDD and DEVDD are analog and digital supply voltage pins of the AT86RF231 radio
transceiver.
AVDD, DVDD
AVDD and DVDD are outputs of the internal 1.8V voltage regulators. The voltage regulators are
controlled independently by the radio transceivers state machine and are activated dependent
on the current radio transceiver state. The voltage regulators can be configured for external
supply.
For details, refer to
AVSS, DVSS
AVSS and DVSS are analog and digital ground pins respectively. The analog and digital power
domains should be separated on the PCB.
RFN, RFP
A differential RF port (RFP/RFN) provides common-mode rejection to suppress the switching
noise of the internal digital signal processing blocks. At board-level, the differential RF layout
ensures high receiver sensitivity by rejecting any spurious emissions originated from other digital
ICs such as a microcontroller.
A simplified schematic of the RF front end is shown in
Figure 1-2.
The RF port is designed for a 100Ω differential load. A DC path between the RF pins is allowed.
A DC path to ground or supply voltage is not allowed. Therefore, when connecting an RF-load
providing a DC path to the power supply or ground, AC-coupling is required as indicated in
1-2 on page
6.
Simplified RF Front-end Schematic
Section 9.4 “Voltage Regulators (AVREG, DVREG)” on page
RFP
RFN
PCB
AT86RF231
M0
0.9V
RXTX
Figure 1-2 on page
CM
Feedback
LNA
PA
RX
TX
AT86RF231
5.
110.
Table
5
Related parts for ATmega1284PR231
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Microcontroller with 128K bytes In-system programmable flash, 8 MHz, power supply =2.7 - 5.5V
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Microcontroller with 128K Bytes In-System Programmable Flash
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
IC AVR MCU 2.4GHZ XCEIVER 64QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ATMEGA644/AT86RF230 40-DIP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
BUNDLE ATMEGA644P/AT86RF230 QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
BUNDLE ATMEGA644P/AT86RF230 TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ATMEGA1281/AT86RF230 64-TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU, 8BIT, AVR, 16K FLASH, 28PDIP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
Microcontroller Modules MCU CARD BIGAVR6 100P W/ ATMEGA2560
Manufacturer:
mikroElektronika