LM3S3768 Luminary Micro, Inc, LM3S3768 Datasheet - Page 257

• Manufacturer Part Number: LM3S3768
• Description: Lm3s3768 Arm Microcontroller
• Manufacturer: Luminary Micro, Inc

Table 10-3. GPIO Register Map
June 02, 2008
Offset
0x40C
0x41C
0x50C
0x000
0x400
0x404
0x408
0x410
0x414
0x418
0x420
0x500
0x504
0x508
0x510
Name
GPIODATA
GPIODIR
GPIOIS
GPIOIBE
GPIOIEV
GPIOIM
GPIORIS
GPIOMIS
GPIOICR
GPIOAFSEL
GPIODR2R
GPIODR4R
GPIODR8R
GPIOODR
GPIOPUR
■
■
Important:
Note:
GPIO Port H (legacy): 0x4002.7000
GPIO Port H (high-speed): 0x4005.F000
The default reset value for the GPIOAFSEL, GPIOPUR, and GPIODEN registers are
0x0000.0000 for all GPIO pins, with the exception of the four JTAG/SWD pins (PC[3:0]).
These four pins default to JTAG/SWD functionality. Because of this, the default reset value
of these registers for Port C is 0x0000.000F.
The default register type for the GPIOCR register is RO for all GPIO pins, with the exception
of the NMI pin and the four JTAG/SWD pins (PB7 and PC[3:0]). These five pins are
currently the only GPIOs that are protected by the GPIOCR register. Because of this, the
register type for GPIO Port B7 and GPIO Port C[3:0] is R/W.
The default reset value for the GPIOCR register is 0x0000.00FF for all GPIO pins, with the
exception of the NMI pin and the four JTAG/SWD pins (PB7 and PC[3:0]). To ensure that
the JTAG port is not accidentally programmed as a GPIO, these four pins default to
non-committable. To ensure that the NMI pin is not accidentally programmed as the
non-maskable interrupt pin, it defaults to non-committable. Because of this, the default reset
value of GPIOCR for GPIO Port B is 0x0000.007F while the default reset value of GPIOCR
for Port C is 0x0000.00F0.
The GPIO registers in this chapter are duplicated in each GPIO block, however,
depending on the block, all eight bits may not be connected to a GPIO pad. In those
cases, writing to those unconnected bits has no effect and reading those unconnected
bits returns no meaningful data.
Type
W1C
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
RO
RO
0x0000.0000
0x0000.0000
0x0000.0000
0x0000.0000
0x0000.0000
0x0000.0000
0x0000.0000
0x0000.0000
0x0000.0000
0x0000.00FF
0x0000.0000
0x0000.0000
0x0000.0000
Reset
-
-
Preliminary
Description
GPIO Data
GPIO Direction
GPIO Interrupt Sense
GPIO Interrupt Both Edges
GPIO Interrupt Event
GPIO Interrupt Mask
GPIO Raw Interrupt Status
GPIO Masked Interrupt Status
GPIO Interrupt Clear
GPIO Alternate Function Select
GPIO 2-mA Drive Select
GPIO 4-mA Drive Select
GPIO 8-mA Drive Select
GPIO Open Drain Select
GPIO Pull-Up Select
LM3S3768 Microcontroller
page
See
259
260
261
262
263
264
265
266
268
269
271
272
273
274
275
257