MC9S08JM32CLD Freescale Semiconductor, MC9S08JM32CLD Datasheet - Page 102

• Manufacturer Part Number: MC9S08JM32CLD
• Description: IC MCU 8BIT 32K FLASH 44-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08JM32CLD

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, LIN, SCI, SPI, USB
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 33
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-LQFP
• Processor Series: S08JM
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: SCI/SPI
• Maximum Clock Frequency: 24 MHz
• Number Of Programmable I/os: 33
• Number Of Timers: 8
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMOJM, DEMOJMSKT, DEMOFLEXISJMSD, DEMO9S08JM16
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 12-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Chapter 7 Central Processor Unit (S08CPUV2)
102
Field
V
H
N
Z
C
7
4
3
2
1
0
I
Two’s Complement Overflow Flag — The CPU sets the overflow flag when a two’s complement overflow occurs.
The signed branch instructions BGT, BGE, BLE, and BLT use the overflow flag.
0 No overflow
1 Overflow
Half-Carry Flag — The CPU sets the half-carry flag when a carry occurs between accumulator bits 3 and 4 during
an add-without-carry (ADD) or add-with-carry (ADC) operation. The half-carry flag is required for binary-coded
decimal (BCD) arithmetic operations. The DAA instruction uses the states of the H and C condition code bits to
automatically add a correction value to the result from a previous ADD or ADC on BCD operands to correct the
result to a valid BCD value.
0 No carry between bits 3 and 4
1 Carry between bits 3 and 4
Interrupt Mask Bit — When the interrupt mask is set, all maskable CPU interrupts are disabled. CPU interrupts
are enabled when the interrupt mask is cleared. When a CPU interrupt occurs, the interrupt mask is set
automatically after the CPU registers are saved on the stack, but before the first instruction of the interrupt service
routine is executed.
Interrupts are not recognized at the instruction boundary after any instruction that clears I (CLI or TAP). This
ensures that the next instruction after a CLI or TAP will always be executed without the possibility of an intervening
interrupt, provided I was set.
0 Interrupts enabled
1 Interrupts disabled
Negative Flag — The CPU sets the negative flag when an arithmetic operation, logic operation, or data
manipulation produces a negative result, setting bit 7 of the result. Simply loading or storing an 8-bit or 16-bit value
causes N to be set if the most significant bit of the loaded or stored value was 1.
0 Non-negative result
1 Negative result
Zero Flag — The CPU sets the zero flag when an arithmetic operation, logic operation, or data manipulation
produces a result of 0x00 or 0x0000. Simply loading or storing an 8-bit or 16-bit value causes Z to be set if the
loaded or stored value was all 0s.
0 Non-zero result
1 Zero result
Carry/Borrow Flag — The CPU sets the carry/borrow flag when an addition operation produces a carry out of bit
7 of the accumulator or when a subtraction operation requires a borrow. Some instructions — such as bit test and
branch, shift, and rotate — also clear or set the carry/borrow flag.
0 No carry out of bit 7
1 Carry out of bit 7
CONDITION CODE REGISTER
Table 7-1. CCR Register Field Descriptions
Figure 7-2. Condition Code Register
MC9S08JM60 Series Data Sheet, Rev. 3
V 1 1 H I N Z
7
Description
0
C
CARRY
ZERO
NEGATIVE
INTERRUPT MASK
HALF-CARRY (FROM BIT 3)
TWO’S COMPLEMENT OVERFLOW
CCR
Freescale Semiconductor