MC9S08JM32CLD Freescale Semiconductor, MC9S08JM32CLD Datasheet - Page 350

• Manufacturer Part Number: MC9S08JM32CLD
• Description: IC MCU 8BIT 32K FLASH 44-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08JM32CLD

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, LIN, SCI, SPI, USB
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 33
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-LQFP
• Processor Series: S08JM
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: SCI/SPI
• Maximum Clock Frequency: 24 MHz
• Number Of Programmable I/os: 33
• Number Of Timers: 8
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMOJM, DEMOJMSKT, DEMOFLEXISJMSD, DEMO9S08JM16
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 12-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Appendix A Electrical Characteristics
A.4
This section provides information about operating temperature range, power dissipation, and package
thermal resistance. Power dissipation on I/O pins is usually small compared to the power dissipation in
on-chip logic and it is user-determined rather than being controlled by the MCU design. In order to take
P
V
loads), the difference between pin voltage and V
350
I/O
DD
into account in power calculations, determine the difference between actual pin voltage and V
Num
and multiply by the pin current for each I/O pin. Except in cases of unusually high pin current (heavy
1
2
3
Thermal Characteristics
C
T Operating temperature range (packaged)
D Maximum junction temperature
T
1
2
3
Supply voltage
Input voltage
Instantaneous maximum current
Maximum current into V
Storage temperature
Input must be current limited to the value specified. To determine the value of the required
current-limiting resistor, calculate resistance values for positive (V
voltages, then use the larger of the two resistance values.
All functional non-supply pins are internally clamped to V
Power supply must maintain regulation within operating V
operating maximum current conditions. If positive injection current (V
I
out of regulation. Ensure external V
current. This will be the greatest risk when the MCU is not consuming power. Examples are: if
no system clock is present, or if the clock rate is very low which would reduce overall power
consumption.
Single pin limit (applies to all port pins)
Thermal resistance
DD
Single layer board
Four layer board
, the injection current may flow out of V
Rating
Rating
DD
Table A-2. Absolute Maximum Ratings
MC9S08JM60 Series Data Sheet, Rev. 3
Table A-3. Thermal Characteristics
64-pin LQFP
44-pin LQFP
64-pin LQFP
44-pin LQFP
DD
48-pin QFN
48-pin QFN
64-pin QFP
64-pin QFP
load will shunt current greater than maximum injection
1
,
2
SS
DD
,
3
or V
and could result in external power supply going
DD
Symbol
Symbol
θ
will be very small.
T
T
T
V
JA
A
V
I
J
I
DD
stg
DD
SS
D
In
DD
and V
range during instantaneous and
DD
– 0.3 to V
DD
) and negative (V
– 0.3 to + 5.8
.
–55 to +150
In
–40 to 85
> V
Value
Value
135
± 25
55
73
84
71
41
54
28
49
120
DD
DD
) is greater than
+ 0.3
Freescale Semiconductor
SS
) clamp
°C/W
Unit
Unit
mA
mA
°C
°C
°C
V
V
Temp.
Code
—
C
SS
or