MC9S08JM32CLD Freescale Semiconductor, MC9S08JM32CLD Datasheet - Page 158

• Manufacturer Part Number: MC9S08JM32CLD
• Description: IC MCU 8BIT 32K FLASH 44-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08JM32CLD

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, LIN, SCI, SPI, USB
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 33
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-LQFP
• Processor Series: S08JM
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: SCI/SPI
• Maximum Clock Frequency: 24 MHz
• Number Of Programmable I/os: 33
• Number Of Timers: 8
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMOJM, DEMOJMSKT, DEMOFLEXISJMSD, DEMO9S08JM16
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 12-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Analog-to-Digital Converter (S08ADC12V1)
For proper conversion, the input voltage must fall between V
exceeds V
(full scale 10-bit representation) or 0xFF (full scale 8-bit representation). If the input is equal to or less
than V
straight-line linear conversions. There is a brief current associated with V
capacitor is charging. The input is sampled for 3.5 cycles of the ADCK source when ADLSMP is low, or
23.5 cycles when ADLSMP is high.
For minimal loss of accuracy due to current injection, pins adjacent to the analog input pins should not be
transitioning during conversions.
10.6.2
Several sources of error exist for A/D conversions. These are discussed in the following sections.
10.6.2.1
For proper conversions, the input must be sampled long enough to achieve the proper accuracy. Given the
maximum input resistance of approximately 7kΩ and input capacitance of approximately 5.5 pF, sampling
to within 1/4
8 MHz maximum ADCK frequency) provided the resistance of the external analog source (R
below 2 kΩ.
Higher source resistances or higher-accuracy sampling is possible by setting ADLSMP (to increase the
sample window to 23.5 cycles) or decreasing ADCK frequency to increase sample time.
10.6.2.2
Leakage on the I/O pins can cause conversion error if the external analog source resistance (R
If this error cannot be tolerated by the application, keep R
1/4
10.6.2.3
System noise that occurs during the sample or conversion process can affect the accuracy of the
conversion. The ADC accuracy numbers are guaranteed as specified only if the following conditions are
met:
158
LSB
•
•
•
•
•
REFL
leakage error (N = 8 in 8-bit, 10 in 10-bit or 12 in 12-bit mode).
There is a 0.1 μF low-ESR capacitor from V
There is a 0.1 μF low-ESR capacitor from V
If inductive isolation is used from the primary supply, an additional 1 μF capacitor is placed from
V
V
Operate the MCU in wait or stop3 mode before initiating (hardware triggered conversions) or
immediately after initiating (hardware or software triggered conversions) the ADC conversion.
— For software triggered conversions, immediately follow the write to ADCSC1 with a wait
DDAD
SSAD
REFH
instruction or stop instruction.
, the converter circuit converts it to 0x000. Input voltages between V
Sources of Error
LSB
Sampling Error
Pin Leakage Error
Noise-Induced Errors
(and V
, the converter circuit converts the signal to 0xFFF (full scale 12-bit representation), 0x3FF
to V
(at 12-bit resolution) can be achieved within the minimum sample window (3.5 cycles @
SSAD
REFL
.
, if connected) is connected to V
MC9S08JM60 Series Data Sheet, Rev. 3
REFH
DDAD
AS
to V
to V
SS
lower than V
REFH
at a quiet point in the ground plane.
REFL
SSAD
and V
.
.
DDAD
REFL
REFL
. If the input is equal to or
when the sampling
/ (2
REFH
N
*I
Freescale Semiconductor
LEAK
and V
) for less than
REFL
AS
AS
) is kept
) is high.
are