MC9S08JM32CLD Freescale Semiconductor, MC9S08JM32CLD Datasheet - Page 132

• Manufacturer Part Number: MC9S08JM32CLD
• Description: IC MCU 8BIT 32K FLASH 44-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08JM32CLD

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, LIN, SCI, SPI, USB
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 33
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-LQFP
• Processor Series: S08JM
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: SCI/SPI
• Maximum Clock Frequency: 24 MHz
• Number Of Programmable I/os: 33
• Number Of Timers: 8
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMOJM, DEMOJMSKT, DEMOFLEXISJMSD, DEMO9S08JM16
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 12-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Keyboard Interrupts (S08KBIV2)
9.4
This on-chip peripheral module is called a keyboard interrupt (KBI) module because originally it was
designed to simplify the connection and use of row-column matrices of keyboard switches. However, these
inputs are also useful as extra external interrupt inputs and as an external means of waking the MCU from
stop or wait low-power modes.
The KBI module allows up to eight pins to act as additional interrupt sources. Writing to the KBIPEn bits
in the keyboard interrupt pin enable register (KBIPE) independently enables or disables each KBI pin.
Each KBI pin can be configured as edge sensitive or edge and level sensitive based on the KBMOD bit in
the keyboard interrupt status and control register (KBISC). Edge sensitive can be software programmed to
be either falling or rising; the level can be either low or high. The polarity of the edge or edge and level
sensitivity is selected using the KBEDGn bits in the keyboard interrupt edge select register (KBIES).
9.4.1
Synchronous logic is used to detect edges. A falling edge is detected when an enabled keyboard interrupt
(KBIPEn=1) input signal is seen as a logic 1 (the deasserted level) during one bus cycle and then a logic 0
(the asserted level) during the next cycle. A rising edge is detected when the input signal is seen as a logic
0 (the deasserted level) during one bus cycle and then a logic 1 (the asserted level) during the next
cycle.Before the first edge is detected, all enabled keyboard interrupt input signals must be at the
deasserted logic levels. After any edge is detected, all enabled keyboard interrupt input signals must return
to the deasserted level before any new edge can be detected.
A valid edge on an enabled KBI pin will set KBF in KBISC. If KBIE in KBISC is set, an interrupt request
will be presented to the CPU. Clearing of KBF is accomplished by writing a 1 to KBACK in KBISC.
9.4.2
A valid edge or level on an enabled KBI pin will set KBF in KBISC. If KBIE in KBISC is set, an interrupt
request will be presented to the CPU. Clearing of KBF is accomplished by writing a 1 to KBACK in
132
KBEDGn
Field
7:0
Reset:
Functional Description
Keyboard Edge Selects — Each of the KBEDGn bits selects the falling edge/low level or rising edge/high level
function of the corresponding pin).
0 Falling edge/low level.
1 Rising edge/high level.
W
Edge Only Sensitivity
Edge and Level Sensitivity
R
KBEDG7
0
7
KBEDG6
0
6
Table 9-4. KBIES Register Field Descriptions
Figure 9-5. KBI Edge Select Register
MC9S08JM60 Series Data Sheet, Rev. 3
KBEDG5
5
0
KBEDG4
0
4
Description
KBEDG3
0
3
KBEDG2
0
2
KBEDG1
0
1
Freescale Semiconductor
KBEDG0
0
0