AT32UC3C2256C Atmel Corporation, AT32UC3C2256C Datasheet - Page 1196

• Manufacturer Part Number: AT32UC3C2256C
• Manufacturer: Atmel Corporation

Specifications of AT32UC3C2256C

• Flash (kbytes): 256 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 45
• Ext Interrupts: 64
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 5
• Twi (i2c): 2
• Uart: 4
• Can: 2
• Lin: 4
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 2
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 12
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 68
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6 or 4.5 to 5.5
• Operating Voltage (vcc): 3.0 to 3.6 or 4.5 to 5.5
• Fpu: Yes
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 13
• Input Capture Channels: 6
• Pwm Channels: 14
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

39.3
39.3.1
39.3.2
39.3.3
32117C–AVR-08/11
On-Chip Debug
Features
Overview
I/O Lines Description
Rev: 2.0.0.0
•
•
•
•
•
•
•
•
Debugging on the AT32UC3C is facilitated by a powerful On-Chip Debug (OCD) system. The
user accesses this through an external debug tool which connects to the JTAG or aWire port
and the Auxiliary (AUX) port if implemented. The AUX port is primarily used for trace functions,
and an aWire- or JTAG-based debugger is sufficient for basic debugging.
The debug system is based on the Nexus 2.0 standard, class 2+, which includes:
In addition to the mandatory Nexus debug features, the AT32UC3C implements several useful
OCD features, such as:
The OCD features are controlled by OCD registers, which can be accessed by the debugger, for
instance when the NEXUS_ACCESS JTAG instruction is loaded. The CPU can also access
OCD registers directly using mtdr/mfdr instructions in any privileged mode. The OCD registers
are implemented based on the recommendations in the Nexus 2.0 standard, and are detailed in
the AVR32UC Technical Reference Manual.
The OCD AUX trace port contains a number of pins, as shown in
These are multiplexed with I/O Controller lines, and must explicitly be enabled by writing OCD
registers before the debug session starts. The AUX port is mapped to two different locations,
• Basic run-time control
• Program breakpoints
• Data breakpoints
• Program trace
• Ownership trace
• Data trace
• Debug Communication Channel between CPU and debugger
• Run-time PC monitoring
• CRC checking
• NanoTrace
• Software Quality Assurance (SQA) support
Debug interface in compliance with IEEE-ISTO 5001-2003 (Nexus 2.0) Class 2+
JTAG or aWire access to all on-chip debug functions
Advanced Program, Data, Ownership, and Watchpoint trace supported
NanoTrace aWire- or JTAG-based trace access
Auxiliary port for high-speed trace information
Hardware support for 6 Program and 2 Data breakpoints
Unlimited number of software breakpoints supported
Automatic CRC check of memory regions
Table 39-5 on page
AT32UC3C
1197.
1196