AT32UC3C2256C Atmel Corporation, AT32UC3C2256C Datasheet - Page 1239

• Manufacturer Part Number: AT32UC3C2256C
• Manufacturer: Atmel Corporation

Specifications of AT32UC3C2256C

• Flash (kbytes): 256 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 45
• Ext Interrupts: 64
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 5
• Twi (i2c): 2
• Uart: 4
• Can: 2
• Lin: 4
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 2
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 12
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 68
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6 or 4.5 to 5.5
• Operating Voltage (vcc): 3.0 to 3.6 or 4.5 to 5.5
• Fpu: Yes
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 13
• Input Capture Channels: 6
• Pwm Channels: 14
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

39.6.7.10
32117C–AVR-08/11
MEMORY_READ
The length field is set to 0x0009 because there are 9 bytes of additional data: 5 address and size
bytes and 4 bytes of data. The address and size field indicates that words should be written to
address 0x500000004. The data written to 0x500000004 is 0xCAFEBABE.
Table 39-41. MEMORY_WRITE Details
This command enables reading of memory/registers on the Service Access Bus (SAB). The
MEMORY_READ command allows words, halfwords, and bytes to be read from a continuous
sequence of addresses in one operation. The user must supply:
The 4 MSB of the 36 bit SAB address are submitted together with the size field (2 bits). The 4
remaining address bytes are submitted before the number of bytes to read. The size of the
transfer is specified using the values from the following table:
Table 39-42. Size Field Decoding
Below is an example read command:
Command
Command value
Additional data
Possible responses
Size field
00
01
10
11
4. 0x09 (length LSB)
5. 0x25 (size and address MSB, the two MSB of this byte are unused and set to zero)
6. 0x00
7. 0x00
8. 0x00
9. 0x04 (address LSB)
10. 0xCA
11. 0xFE
12. 0xBA
13. 0xBE
14. 0xXX (CRC MSB)
15. 0xXX (CRC LSB)
1. The size of the data field: 7 (size and starting address + read length indicator) in the
2. The size of the transfer: Words, halfwords, or bytes.
3. The starting address of the transfer.
4. The number of bytes to read (max 65532).
length field.
Details
0x80
Size, Address and Data
0xC2: MEMORY_READWRITE_STATUS
0x41: NACK
Description
Byte transfer
Halfword transfer
Word transfer
Reserved
(Section
39.6.8.2)
AT32UC3C
(Section
39.6.8.5)
1239