AT32UC3C2256C Atmel Corporation, AT32UC3C2256C Datasheet - Page 361

• Manufacturer Part Number: AT32UC3C2256C
• Manufacturer: Atmel Corporation

Specifications of AT32UC3C2256C

• Flash (kbytes): 256 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 45
• Ext Interrupts: 64
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 5
• Twi (i2c): 2
• Uart: 4
• Can: 2
• Lin: 4
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 2
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 12
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 68
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6 or 4.5 to 5.5
• Operating Voltage (vcc): 3.0 to 3.6 or 4.5 to 5.5
• Fpu: Yes
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 13
• Input Capture Channels: 6
• Pwm Channels: 14
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

19.8.1
Register Name:
Access Type:
Offset:
Reset Value:
• MODE: Command Mode
32117C–AVR-08/11
MODE
0
1
2
3
4
5
6
31
23
15
7
-
-
-
-
This field defines the command issued by the SDRAMC when the SDRAM device is accessed.
Mode Register
Description
Normal mode. Any access to the SDRAM is decoded normally.
The SDRAMC issues a “NOP” command when the SDRAM device is accessed regardless of the cycle.
The SDRAMC issues an “All Banks Precharge” command when the SDRAM device is accessed regardless of
the cycle.
The SDRAMC issues a “Load Mode Register” command when the SDRAM device is accessed regardless of the
cycle. This command will load the CR.CAS field into the SDRAM device Mode Register. All the other parameters
of the SDRAM device Mode Register will be set to zero (burst length, burst type, operating mode, write burst
mode...).
The SDRAMC issues an “Auto Refresh” command when the SDRAM device is accessed regardless of the cycle.
Previously, an “All Banks Precharge” command must be issued.
The SDRAMC issues an “Extended Load Mode Register” command when the SDRAM device is accessed
regardless of the cycle. This command will load the LPR.PASR, LPR.DS, and LPR.TCR fields into the SDRAM
device Extended Mode Register. All the other bits of the SDRAM device Extended Mode Register will be set to
zero.
Deep power-down mode. Enters deep power-down mode.
30
22
14
6
-
-
-
-
MR
Read/Write
0x00
0x00000000
29
21
13
5
-
-
-
-
28
20
12
4
-
-
-
-
27
19
11
3
-
-
-
-
26
18
10
2
-
-
-
MODE
25
17
9
1
-
-
-
AT32UC3C
24
16
8
0
-
-
-
361