AT32UC3C2256C Atmel Corporation, AT32UC3C2256C Datasheet - Page 704

• Manufacturer Part Number: AT32UC3C2256C
• Manufacturer: Atmel Corporation

Specifications of AT32UC3C2256C

• Flash (kbytes): 256 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 45
• Ext Interrupts: 64
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 5
• Twi (i2c): 2
• Uart: 4
• Can: 2
• Lin: 4
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 2
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 12
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 68
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6 or 4.5 to 5.5
• Operating Voltage (vcc): 3.0 to 3.6 or 4.5 to 5.5
• Fpu: Yes
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 13
• Input Capture Channels: 6
• Pwm Channels: 14
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

Figure 27-7. Master Write with Multiple Data Bytes
27.8.4
32117C–AVR-08/11
SR.IDLE
TXRDY
TWD
Master Receiver Mode
NBYTES set to n
S
Write THR
(DATAn)
DADR
does not acknowledge the data byte. As with the other status bits, an interrupt can be generated
if enabled in the Interrupt Enable Register (IER).
TXRDY is used as Transmit Ready for the Peripheral DMA Controller transmit channel.
The end of a command is marked by writing a one to the SR.CCOMP bit. See
Figure
Figure 27-6. Master Write with One Data Byte
A START condition is transmitted and master receiver mode is initiated when the bus is free and
CMDR has been written with START=1 and READ=1. START and SADR+R will then be trans-
mitted. During the address acknowledge clock pulse (9th pulse), the master releases the data
line (HIGH), enabling the slave to pull it down in order to acknowledge the address. The master
polls the data line during this clock pulse and writes a one to the Address Not Acknowledged bit
(ANAK) in the Status Register if no slave acknowledges the address.
After the address phase, the following is repeated:
while (NBYTES>0)
SR.IDLE
1. Wait until RHR is empty, stretching low period of TWCK. SR.RXRDY indicates the state
2. Release TWCK generating a clock that the slave uses to transmit a data byte.
3. Place the received data byte in RHR, write a one to RXRDY.
4. If NBYTES=0, generate a NAK after the data byte, otherwise generate an ACK.
TXRDY
W
of RHR. Software or the Peripheral DMA Controller must read any data byte present in
RHR.
TWD
27-7.
A
Write THR (DATA)
NBYTES set to 1
S
(DATAn+1)
Write THR
DATAn
DADR
A
W
A
DATAn+5
Last data sent
(DATAn+m)
Write THR
DATA
(ACK received and NBYTES=0)
A
STOP sent automatically
A
DATAn+m
P
(ACK received and NBYTES=0)
STOP sent automatically
A
AT32UC3C
P
Figure 27-6
and
704