MCF5307AI90B Freescale Semiconductor, MCF5307AI90B Datasheet - Page 205

• Manufacturer Part Number: MCF5307AI90B
• Description: IC MPU 32BIT COLDF 90MHZ 208FQFP
• Manufacturer: Freescale Semiconductor
• Series: MCF530xr

Specifications of MCF5307AI90B

• Core Processor: Coldfire V3
• Core Size: 32-Bit
• Speed: 90MHz
• Connectivity: EBI/EMI, I²C, UART/USART
• Peripherals: DMA, POR, WDT
• Number Of I /o: 16
• Program Memory Type: ROMless
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 208-FQFP
• Maximum Clock Frequency: 90 MHz
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: 0 C
• Family Name: MCF5xxx
• Device Core: ColdFire
• Device Core Size: 32b
• Frequency (max): 90MHz
• Instruction Set Architecture: RISC
• Supply Voltage 1 (typ): 3.3V
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 208
• Package Type: FQFP
• Program Memory Size: 8KB
• Cpu Speed: 90MHz
• Embedded Interface Type: I2C, UART
• Digital Ic Case Style: FQFP
• No. Of Pins: 208
• Supply Voltage Range: 3V To 3.6V
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

8.3 I
The I
For I
open collector outputs. (There is no such requirement for inputs.) The logic AND function
is exercised on both lines with external pull-up resistors.
Out of reset, the I
or responding to a slave transmit address, the I
receiver state. See Section 8.6.1, “Initialization Sequence,” for exceptions.
8.4 I
Normally, a standard communication is composed of the following parts:
1. START signal—When no other device is bus master (both SCL and SDA lines are
SCL
2. Slave address transmission—The master sends the slave address in the first byte
A
SDA
2
2
C compliance, all devices connected to these two signals must have open drain or
C module uses a serial data line (SDA) and a serial clock line (SCL) for data transfer.
START
Signal
at logic high), a device can initiate communication by sending a START signal (see
A in Figure 8-2). A START signal is defined as a high-to-low transition of SDA
while SCL is high. This signal denotes the beginning of a data transfer (each data
transfer can be several bytes long) and awakens all slaves.
after the START signal (B). After the seven-bit calling address, it sends the R/W bit
(C), which tells the slave data transfer direction.
Each slave must have a unique address. An I
that is the same as its slave address; it cannot be master and slave at the same time.
2
2
AD7 AD6 AD5 AD4 AD3 AD2 AD1 R/W
C System Configuration
C Protocol
msb
1
The I
I
protocol, and restrictions, see The I
Version 2.1.
2
2
C bus protocol. For information on system configuration,
Calling Address
2
Figure 8-2. I
3
C default is as slave receiver. Thus, when not programmed to be a master
2
C module is designed to be compatible with the Philips
B
4
Freescale Semiconductor, Inc.
5
For More Information On This Product,
6
2
C Standard Communication Protocol
7
Go to: www.freescale.com
Chapter 8. I
R/W ACK
lsb
8
C
Bit
9
NOTE:
D
XXX
2
C Module
2
C module should return to the default slave
msb
D7 D6 D5
1
2
E
C master must not transmit an address
2
C Bus Specification,
2
3
Data Byte
D4 D3 D2 D1 D0
4
5
I
2
C System Configuration
6
7
lsb
8
ACK
No
Bit
9
STOP
Signal
F
8-3