MCF5307AI90B Freescale Semiconductor, MCF5307AI90B Datasheet - Page 280

• Manufacturer Part Number: MCF5307AI90B
• Description: IC MPU 32BIT COLDF 90MHZ 208FQFP
• Manufacturer: Freescale Semiconductor
• Series: MCF530xr

Specifications of MCF5307AI90B

• Core Processor: Coldfire V3
• Core Size: 32-Bit
• Speed: 90MHz
• Connectivity: EBI/EMI, I²C, UART/USART
• Peripherals: DMA, POR, WDT
• Number Of I /o: 16
• Program Memory Type: ROMless
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 208-FQFP
• Maximum Clock Frequency: 90 MHz
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: 0 C
• Family Name: MCF5xxx
• Device Core: ColdFire
• Device Core Size: 32b
• Frequency (max): 90MHz
• Instruction Set Architecture: RISC
• Supply Voltage 1 (typ): 3.3V
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 208
• Package Type: FQFP
• Program Memory Size: 8KB
• Cpu Speed: 90MHz
• Embedded Interface Type: I2C, UART
• Digital Ic Case Style: FQFP
• No. Of Pins: 208
• Supply Voltage Range: 3V To 3.6V
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

DMA Signal Description
12.1.1 DMA Module Features
The DMA controller module features are as follows:
12.2 DMA Signal Description
Table 12-1 briefly describes the DMA module signals that provide handshake control for
either a source or destination external device.
12-2
DREQ[1:0]/
PP[6:5]
TT[1:0]/
PP[1:0]
TM[2:0]
/PP[4:2]
Signal
• Four fully independent, programmable DMA controller channels/bus modules
• Auto-alignment feature for source or destination accesses
• Dual- and single-address transfers
• Two external request pins (DREQ[1:0]) provided for channels 1 and 0
• Channel arbitration on transfer boundaries
• Data transfers in 8-, 16-, 32-, or 128-bit blocks using a 16-byte buffer
• Continuous-mode and cycle-steal transfers
• Independent transfer widths for source and destination
• Independent source and destination address registers
• Data transfer can occur in as few as two clocks
I/O
O
O
I
External DMA request. DREQ[1:0] can serve as the DMA request inputs or as two parallel port
bits. They are programmable individually through the PAR. A peripheral device asserts these
inputs to request an operand transfer between it and memory.
DREQ signals are asserted to initiate DMA accesses in the respective channels. The system
should drive unused DREQ signals to logic high. Although each channel has an individual
DREQ signal, in the MCF5307 only channels 0 and 1 connect to external DREQ pins.DREQ
signals for channels 2 and 3 are connected to the UART0 and UART1 bus interrupt signals.
Transfer type. A DMA access is indicated by the transfer type pins, TT[1:0] = 01. The transfer
modifier, TM[2:0] configurations shown below are meaningful only if TT[1:0] = 01, indicating an
external master or DMA access.
Multiplexed transfer attribute pins. The encodings below are valid when TT[1:0] = 01 and
internal DMA channels are driving the bus. DMA transfer information on TM[2:1] can be
provided on every DMA transfer or only on the last transfer by programming DCR[AT].
TM[2:1]Encoding
00
01
10
11
TM0
0
1
For TT[1:0] = 01, the TM0 encoding is independent of TM[2:1]. If DCR[SAA] is set, TM0
designates a single-address DMA access.
DMA acknowledge information not provided
DMA transfer, channel 0
DMA transfer, channel 1
Reserved
Encoding for DMA as master (TT = 01)
Single-address access negated
Single-address access
Freescale Semiconductor, Inc.
For More Information On This Product,
Table 12-1. DMA Signals
Go to: www.freescale.com
MCF5307 User’s Manual
Description