PIC18F46K22-I/MV Microchip Technology, PIC18F46K22-I/MV Datasheet - Page 35

• Manufacturer Part Number: PIC18F46K22-I/MV
• Description: 64KB, Flash, 3968bytes-RAM,8-bit Family,nanoWatt XLP 40 UQFN 5x5x0.5mm TUBE
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F46K22-I/MV

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 64MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 35
• Program Memory Size: 64KB (32K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 30x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 40-UFQFN Exposed Pad
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 4 KB
• Number Of Programmable I/os: 36
• Number Of Timers: 3 x 8-bit. 4 x 16-bit
• Operating Supply Voltage: 1.8 V to 5.5 V
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

2.4.3
The LP, XT and HS modes support the use of quartz
crystal resonators or ceramic resonators connected to
OSC1 and OSC2
medium or high gain setting of the internal inverter-
amplifier to support various resonator types and speed.
LP Oscillator mode selects the lowest gain setting of the
internal inverter-amplifier. LP mode current consumption
is the least of the three modes. This mode is best suited
to drive resonators with a low drive level specification, for
example, tuning fork type crystals.
XT Oscillator mode selects the intermediate gain
setting of the internal inverter-amplifier. XT mode
current consumption is the medium of the three modes.
This mode is best suited to drive resonators with a
medium drive level specification.
HS Oscillator mode offers a Medium Power (MP) and a
High Power (HP) option selectable by the FOSC<3:0>
bits. The MP selections are best suited for oscillator
frequencies between 4 and 16 MHz. The HP selection
has the highest gain setting of the internal inverter-
amplifier and is best suited for frequencies above
16 MHz. HS mode is best suited for resonators that
require a high drive setting.
FIGURE 2-6:
 2010 Microchip Technology Inc.
Note 1: A series resistor (R
C1
C2
2: The value of R
quartz crystals with low drive level.
selected (typically between 2 M to 10 M.
LP, XT, HS MODES
Quartz
Crystal
R
S (1)
(Figure
QUARTZ CRYSTAL
OPERATION (LP, XT OR
HS MODE)
F
varies with the Oscillator mode
2-6). The mode selects a low,
OSC1/CLKIN
OSC2/CLKOUT
R
S
F
) may be required for
(2)
PIC
®
MCU
Sleep
To Internal
Logic
Preliminary
FIGURE 2-7:
Note 1: A series resistor (R
Note 1: Quartz
PIC18(L)F2X/4XK22
C1
C2 Ceramic
2: The value of R
3: An additional parallel feedback resistor (R
2: Always verify oscillator performance over
3: For oscillator design assistance, refer to the
Resonator
ceramic resonators with low drive level.
selected (typically between 2 M to 10 M.
may be required for proper ceramic resonator
operation.
• AN826, “Crystal Oscillator Basics and
• AN849, “Basic PIC
• AN943, “Practical PIC
• AN949, “Making Your Oscillator Work”
according
manufacturer. The user should consult the
manufacturer data sheets for specifications
and recommended application.
the V
expected for the application.
following Microchip Application Notes:
Crystal Selection for rfPIC
Devices” (DS00826)
(DS00849)
Analysis and Design” (DS00943)
(DS00949)
DD
R
P (3)
R
S
and temperature range that is
(1)
crystal
CERAMIC RESONATOR
OPERATION
(XT OR HS MODE)
F
to
varies with the Oscillator mode
OSC1/CLKIN
OSC2/CLKOUT
type,
S
R
) may be required for
®
F
characteristics
(2)
Oscillator Design”
®
PIC
Oscillator
DS41412D-page 35
®
package
®
and PIC
MCU
To Internal
Logic
Sleep
®
vary
and
P
)