EVB9S12XEP100 Freescale Semiconductor, EVB9S12XEP100 Datasheet - Page 564

• Manufacturer Part Number: EVB9S12XEP100
• Description: BOARD EVAL FOR MC9S12XEP100
• Manufacturer: Freescale Semiconductor
• Type: MCUr

Specifications of EVB9S12XEP100

• Contents: Module and Misc Hardware
• Processor To Be Evaluated: MC9S12XEP100
• Data Bus Width: 16 bit
• Interface Type: RS-232
• Silicon Manufacturer: Freescale
• Core Architecture: S12
• Core Sub-architecture: S12
• Silicon Core Number: MC9S12
• Silicon Family Name: S12XE
• Rohs Compliant: Yes
• For Use With/related Products: MC9S12XEP100
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Chapter 14 Enhanced Capture Timer (ECT16B8CV3)
14.3.2.29 Pulse Accumulator B Flag Register (PBFLG)
Read: Anytime
Write used in the flag clearing mechanism. Writing a one to the flag clears the flag. Writing a zero will not
affect the current status of the bit.
All bits reset to zero.
PBFLG indicates when interrupt conditions have occurred. The flag can be cleared via the normal flag
clearing mechanism (writing a one to the flag) or via the fast flag clearing mechanism (Reference TFFCA
bit in
564
Module Base + 0x0031
Because of an order from the United States International Trade Commission, BGA-packaged product lines and partnumbers
PBOVF
PBOVI
Reset
PBEN
indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010
Field
Field
6
1
1
Section 14.3.2.6, “Timer System Control Register 1
W
R
Pulse Accumulator B System Enable — PBEN is independent from TEN. With timer disabled, the pulse
accumulator can still function unless pulse accumulator is disabled.
0 16-bit pulse accumulator system disabled. 8-bit PAC1 and PAC0 can be enabled when their related enable
1 Pulse accumulator B system enabled. The two 8-bit pulse accumulators PAC1 and PAC0 are cascaded to form
Pulse Accumulator B Overflow Interrupt Enable
0 Interrupt inhibited
1 Interrupt requested if PBOVF is set
Pulse Accumulator B Overflow Flag — This bit is set when the 16-bit pulse accumulator B overflows from
0xFFFF to 0x0000, or when 8-bit pulse accumulator 1 (PAC1) overflows from 0x00FF to 0x0000.
When PACMX = 1, PBOVF bit can also be set if 8-bit pulse accumulator 1 (PAC1) reaches 0x00FF and an active
edge follows on IC1.
0
0
7
bits in ICPAR are set.
the PACB 16-bit pulse accumulator B. When PACB is enabled, the PACN1 and PACN0 registers contents are
respectively the high and low byte of the PACB.
PA1EN and PA0EN control bits in ICPAR have no effect.
The PACB shares the input pin with IC0.
When TFFCA = 1, the flag cannot be cleared via the normal flag clearing
mechanism (writing a one to the flag). Reference
System Control Register 1
= Unimplemented or Reserved
Figure 14-52. Pulse Accumulator B Flag Register (PBFLG)
0
0
6
MC9S12XE-Family Reference Manual Rev. 1.23
Table 14-38. PBFLG Field Descriptions
Table 14-37. PBCTL Field Descriptions
5
0
0
(TSCR1)”.
NOTE
0
0
4
Description
Description
(TSCR1)”).
0
0
3
Section 14.3.2.6, “Timer
2
0
0
PBOVF
Freescale Semiconductor
0
1
0
0
0