ADUC847BCPZ8-5 Analog Devices Inc, ADUC847BCPZ8-5 Datasheet - Page 53

• Manufacturer Part Number: ADUC847BCPZ8-5
• Description: IC,Data Acquisition CODEC,2-CHANNEL,LLCC,56PIN,PLASTIC
• Manufacturer: Analog Devices Inc
• Series: MicroConverter® ADuC8xxr

Specifications of ADUC847BCPZ8-5

• Core Processor: 8052
• Core Size: 8-Bit
• Speed: 12.58MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: POR, PSM, PWM, Temp Sensor, WDT
• Number Of I /o: 34
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 4.75 V ~ 5.25 V
• Data Converters: A/D 10x24b; D/A 1x12b, 2x16b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 56-LFCSP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-ADUC847QSZ - KIT DEV QUICK START FOR ADUC847
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

DAC CIRCUIT INFORMATION
The ADuC845/ADuC847/ADuC848 incorporate a 12-bit,
voltage output DAC on-chip. It has a rail-to-rail voltage output
buffer capable of driving 10 kΩ/100 pF, and has two selectable
ranges, 0 V to V
8-bit mode. The DAC has a control register, DACCON, and two
data registers, DACH/L. The DAC output can be programmed
to appear at Pin 14 (DAC) or Pin 13 (AINCOM).
DACCON Control Register
SFR Address:
Power-On Default:
Bit Addressable:
Table 33. DACCON—DAC Configuration Commands
Bit No.
7
6
5
4
3
2
1
0
DACH/DACL Data Registers
These DAC data registers are written to by the user to update
the DAC output.
SFR Address:
Power-On Default:
Bit Addressable:
Name
–––
–––
–––
DACPIN
DAC8
DACRN
DACCLR
DACEN
REF
and 0 V to AV
FDH
00H
No
DACH (DAC data high byte)—FCH
00H (both registers)
No (both registers)
DACL (DAC data low byte)—FBH
DAC Output Pin Select.
DAC Clear Bit.
DAC Enable Bit.
Description
Not Implemented. Write Don’t Care.
Not Implemented. Write Don’t Care.
Not Implemented. Write Don’t Care.
Set to 1 by the user to direct the DAC output to Pin 13 (AINCOM).
Cleared to 0 by the user to direct the DAC output to Pin 14 (DAC).
DAC 8-Bit Mode Bit.
Set to 1 by the user to enable 8-bit DAC operation. In this mode, the 8 bits in DACL SFR are routed to the 8 MSBs
of the DAC, and the 4 LSBs of the DAC are set to 0.
Cleared to 0 by the user to enable 12-bit DAC operation. In this mode, the 8 LSBs of the result are routed to
DACL, and the upper 4 MSB bits are routed to the lower 4 bits of DACH.
DAC Output Range Bit.
Set to 1 by the user to configure the DAC range of 0 V to AV
Cleared to 0 by the user to configure the DAC range of 0 V to 2.5 V (V
Set to 1 by the user to enable normal DAC operation.
Cleared to 0 by the user to reset the DAC data registers DACL/H to 0.
Set to 1 by the user to enable normal DAC operation.
Cleared to 0 by the user to power down the DAC.
DD
. It can operate in 12-bit or
Rev. B | Page 53 of 108
In 12-bit mode, the DAC voltage output is updated as soon as
the DACL data SFR is written; therefore, the DAC data registers
should be updated as DACH first, followed by DACL. The 12-
bit DAC data should be written into DACH/L right-justified
such that DACL contains the lower 8 bits, and the lower nibble
of DACH contains the upper 4 bits.
DD
.
ADuC845/ADuC847/ADuC848
REF
).