ADUC847BCPZ8-5 Analog Devices Inc, ADUC847BCPZ8-5 Datasheet - Page 92

• Manufacturer Part Number: ADUC847BCPZ8-5
• Description: IC,Data Acquisition CODEC,2-CHANNEL,LLCC,56PIN,PLASTIC
• Manufacturer: Analog Devices Inc
• Series: MicroConverter® ADuC8xxr

Specifications of ADUC847BCPZ8-5

• Core Processor: 8052
• Core Size: 8-Bit
• Speed: 12.58MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: POR, PSM, PWM, Temp Sensor, WDT
• Number Of I /o: 34
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 4.75 V ~ 5.25 V
• Data Converters: A/D 10x24b; D/A 1x12b, 2x16b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 56-LFCSP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-ADUC847QSZ - KIT DEV QUICK START FOR ADUC847
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

ADuC845/ADuC847/ADuC848
The serial port debugger is fully contained on the device, unlike
ROM monitor type debuggers, and, therefore, no external
memory is needed to enable in-system debug sessions.
Single-Pin Emulation Mode
Built into the ADuC845/ADuC847/ADuC848 is a dedicated
controller for single-pin in-circuit emulation (ICE). In this mode,
emulation access is gained by connection to a single pin, the EA
pin. Normally on the 8051 standard, this pin is hardwired either
high or low to select execution from internal or external program
memory space. Note that external program memory or execu-
tion from external program memory is not allowed on the
devices. To enable single-pin emulation mode, users need to
pull the EA pin high through a 1 kΩ resistor as shown in
Figure 70. The emulator then connects to the 2-pin header also
shown in Figure 70. To be compatible with the standard connec-
tor that comes with the single-pin emulator available from
Accutron Limited (www.accutron.com), use a 2-pin 0.1-inch
pitch Friction Lock header from Molex (www.molex.com) such
as part number 22-27-2021. Be sure to observe the polarity of
this header. As shown in Figure 70, when the Friction Lock tab
is at the right, the ground pin should be the lower of the two
pins when viewed from the top.
Typical System Configuration
A typical ADuC845/ADuC847/ADuC848 configuration is
shown in Figure 70. Figure 70 also includes connections for a
typical analog measurement application of the parts, namely an
interface to a resistive temperature device (RTD). The
arrangement shown is commonly referred to as a 4-wire RTD
configuration.
Rev. B | Page 92 of 108
Here, the on-chip excitation current sources are enabled to
excite the sensor. The excitation current flows directly through
the RTD generating a voltage across the RTD proportional to its
resistance. This differential voltage is routed directly to one set
of the positive and negative inputs of the ADC (AIN1, AIN2,
respectively in this case). The same current that excited the
RTD also flows through a series resistance, R
ratiometric voltage reference, V
reference ensures that variations in the excitation current do not
affect the measurement system since the input voltage from the
RTD and reference voltage across R
the excitation current. Resistor R
temperature coefficient to avoid errors in the reference voltage
overtemperature. R
least a 1 V voltage reference.
The preceding example shows just a single differential ADC
connection using a single reference input pair. The ADuC845/
ADuC847/ADuC848 have the capability of connecting to five
differential inputs directly or ten single-ended inputs (LFCSP
package only) as well as having a second reference input. This
arrangement means that different sensors with different
reference ranges can be connected to the part with the need for
external multiplexing circuitry. This arrangement is shown in
Figure 71. The bridge sensor shown can be a load cell or a
pressure sensor. The RTD is shown using a reference voltage
derived from the R
bridge sensor is shown using a divided down AV
the REFIN2± inputs.
REF
REF
resistor via the REFIN± inputs, and the
must also be large enough to generate at
REF
REF
. The ratiometric voltage
REF
must, however, have a low
vary ratiometrically with
REF
, generating a
DD
reference via