LAN91C111I-NS SMSC, LAN91C111I-NS Datasheet - Page 75

• Manufacturer Part Number: LAN91C111I-NS
• Description: IC ETHERNET CTLR MAC PHY 128-QFP
• Manufacturer: SMSC
• Type: Single Chip MAC and PHYr

Specifications of LAN91C111I-NS

• Controller Type: Ethernet Controller, MAC/PHY
• Interface: Serial EEPROM
• Voltage - Supply: 3.3V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 128-QFP
• Product: Ethernet Controllers
• Number Of Transceivers: 1
• Standard Supported: IEEE 802.3 or IEEE 802.3u
• Data Rate: 10 Mbps or 100 Mbps
• Supply Voltage (max): 5 V
• Supply Voltage (min): 0 V
• Supply Current (max): 140 mA
• Maximum Operating Temperature: + 85 C
• Ethernet Connection Type: 100BASE-T or 100BASE-T4 or 100BASE-TX or 10BASE-T
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Supply: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 638-1014

10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
SMSC LAN91C111 REV C
9.2
Reserved
CAP_T4
R
R
0
0
Register 1. Status Register
DPLX - Duplex mode
When Auto Negotiation is disabled this bit can be used to manually select the link duplex state. Writing
a ‘1’ to this bit selects full duplex while a ‘0’ selects half duplex.
When Auto-Negotiation is enabled reading or writing this bit has no effect.
COLTST - Collision test
Setting a ‘1’ allows for testing of the MII COL signal. ‘0’ allows normal operation.
Reserved:Reserved, Must be 0 for Proper Operation
CAP_T4 - 100BASE-T4 Capable
‘1’ Indicates 100Base-T4 capable PHY, ‘0’ not capable.
CAP_TXF - 100BASE-TX Full Duplex Capable
‘1’ Indicates 100Base-X full duplex capable PHY, ‘0’ not capable.
CAP_TXH - 100BASE-TX Half Duplex Capable
‘1’ Indicates 100Base-X alf duplex capable PHY, ‘0’ not capable.
CAP_TF - 10BASE-T Full Duplex Capable
‘1’ Indicates 10Mbps full duplex capable PHY, ‘0’ not capable.
CAP_TH - 10BASE-T Half Duplex Capable
‘1’ Indicates 10Mbps half duplex capable PHY, ‘0’ not capable.
Reserved:Reserved, Must be 0 for Proper Operation.
CAP_SUPR - MI Preamble Suppression Capable
‘1’ indicates the PHY is able to receive management frames even if not preceded by a preamble. ‘0’
when it is not able.
ANEG_ACK - Auto-Negotiation Acknowledgment
When read as ‘1’ indicate ANEG has been completed and that contents in registers 4,5,6 and 7 are
valid. ‘0’ means ANEG has not completed and contents in registers 4,5,6 and 7 are meaningless. The
PHY returns zero if ANEG is disabled.
CAP_SUPR
CAP_TXF
R
R
1
0
CAP_TXH
ANEG_ACK
R
1
R
0
CAP_TF
REM_FLT
DATASHEET
R
R, LH
1
0
75
CAP_TH
CAP_ANEG
R
1
R
1
Reserved
R, LL
LINK
R
0
0
Reserved.
R, LH
JAB
0
R
0
Revision 1.91 (06-01-09)
Reserved
EXREG
R
R
1
0