MC9S12XEP100MAL Freescale Semiconductor, MC9S12XEP100MAL Datasheet - Page 998

• Manufacturer Part Number: MC9S12XEP100MAL
• Description: IC MCU 16BIT 1M FLASH 112-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12XEP100MAL

• Core Processor: HCS12X
• Core Size: 16-Bit
• Speed: 50MHz
• Connectivity: CAN, EBI/EMI, I²C, IrDA, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 91
• Program Memory Size: 1MB (1M x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 1.72 V ~ 5.5 V
• Data Converters: A/D 16x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 112-LQFP
• Processor Series: S12XE
• Core: HCS12
• Data Bus Width: 16 bit
• Data Ram Size: 64 KB
• Interface Type: SPI, SSI
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 91
• Number Of Timers: 25
• Operating Supply Voltage: - 0.3 V to + 6 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Development Tools By Supplier: KIT33812ECUEVME, EVB9S12XEP100, DEMO9S12XEP100
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 16 Channel
• For Use With: EVB9S12XEP100 - BOARD EVAL FOR MC9S12XEP100DEMO9S12XEP100 - BOARD DEMO FOR MC9S12XEP100
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Chapter 26 384 KByte Flash Module (S12XFTM384K2V1)
values for the Program Once command range from 0x0000 to 0x0007. During execution of the Program
Once command, any attempt to read addresses within P-Flash block 0 will return invalid data.
26.4.2.8
The Erase All Blocks operation will erase the entire P-Flash and D-Flash memory space including the EEE
nonvolatile information register.
Upon clearing CCIF to launch the Erase All Blocks command, the Memory Controller will erase the entire
Flash memory space and verify that it is erased. If the Memory Controller verifies that the entire Flash
memory space was properly erased, security will be released. During the execution of this command
(CCIF=0) the user must not write to any Flash module register. The CCIF flag will set after the Erase All
Blocks operation has completed.
998
1. If a Program Once phrase is initially programmed to 0xFFFF_FFFF_FFFF_FFFF, the Program Once command will
be allowed to execute again on that same phrase.
FERSTAT
Register
FSTAT
Erase All Blocks Command
CCOBIX[2:0]
Table 26-47. Erase All Blocks Command FCCOB Requirements
MGSTAT1
MGSTAT0
EPVIOLIF
ACCERR
Error Bit
FPVIOL
000
Table 26-46. Program Once Command Error Handling
MC9S12XE-Family Reference Manual , Rev. 1.23
Set if CCOBIX[2:0] != 101 at command launch
Set if a Load Data Field command sequence is currently active
Set if command not available in current mode (see
Set if an invalid phrase index is supplied
Set if the requested phrase has already been programmed
None
Set if any errors have been encountered during the verify operation
Set if any non-correctable errors have been encountered during the verify
operation
None
0x08
FCCOB Parameters
Error Condition
Not required
Table
26-30)
(1)
Freescale Semiconductor