LPC1113FHN33/303,5 NXP Semiconductors, LPC1113FHN33/303,5 Datasheet - Page 160

• Manufacturer Part Number: LPC1113FHN33/303,5
• Description: ARM Microcontrollers - MCU Cortex-M0 24 kB flash up to 8kB SRAM
• Manufacturer: NXP Semiconductors

Specifications of LPC1113FHN33/303,5

• Rohs: yes
• Core: ARM Cortex M0
• Processor Series: LPC1113
• Data Bus Width: 32 bit
• Maximum Clock Frequency: 50 MHz
• Program Memory Size: 24 KB
• Data Ram Size: 4 KB
• On-chip Adc: Yes
• Operating Supply Voltage: 1.8 V to 3.6 V
• Operating Temperature Range: - 65 C to + 150 C
• Package / Case: HVQFN-33
• Mounting Style: SMD/SMT
• Factory Pack Quantity: 260

NXP Semiconductors
Table 163. LPC11D14 pin description table (LQFP100 package)
[1]
[2]
[3]
[4]
[5]
[6]
[7]
UM10398
User manual
Symbol
S38
S39
BP0
BP1
BP2
BP3
LCD_SDA
LCD_SCL
SYNC
CLK
V
V
V
n.c.
DD(LCD)
SS(LCD)
LCD
Pin state at reset for default function: I = Input; O = Output; PU = internal pull-up enabled (pins pulled up to full V
IA = inactive, no pull-up/down enabled.
RESET functionality is not available in Deep power-down mode. Use the WAKEUP pin to reset the chip and wake up from Deep
power-down mode. An external pull-up resistor is required on this pin for the Deep power-down mode.
5 V tolerant pad providing digital I/O functions with configurable pull-up/pull-down resistors and configurable hysteresis.
I
5 V tolerant pad providing digital I/O functions with configurable pull-up/pull-down resistors, configurable hysteresis, and analog input.
When configured as a ADC input, digital section of the pad is disabled and the pin is not 5 V tolerant.
When the system oscillator is not used, connect XTALIN and XTALOUT as follows: XTALIN can be left floating or can be grounded
(grounding is preferred to reduce susceptibility to noise). XTALOUT should be left floating.
See the LPC11D4 data sheet.
2
C-bus pads compliant with the I
Pin
33
34
42
44
43
45
35
36
37
38
39
40
41
3
Start
logic
input
-
-
-
-
-
-
-
-
-
-
-
-
-
-
2
C-bus specification for I
Chapter 9: LPC111x/LPC11Cxx Pin configuration (LPC1100, LPC1100C,
Type
O
O
O
O
O
O
I/O
I/O
I/O
I/O
-
-
-
-
All information provided in this document is subject to legal disclaimers.
Rev. 12 — 24 September 2012
Reset
state
[1]
V
V
V
V
V
V
[7]
[7]
[7]
[7]
-
-
-
-
LCD
LCD
LCD
LCD
LCD
LCD
2
C standard mode and I
[7]
[7]
[7]
[7]
[7]
[7]
Description
LCD segment output.
LCD segment output.
LCD backplane output.
LCD backplane output.
LCD backplane output.
LCD backplane output.
I
I
Cascade synchronization input/output.
External clock input/output.
1.8 V to 5.5 V power supply: Power supply voltage for the
PCF8576D.
LCD ground.
LCD power supply; LCD voltage.
Not connected.
2
2
C-bus serial data input/output.
C-bus serial clock input.
…continued
2
C Fast-mode Plus.
UM10398
DD
© NXP B.V. 2012. All rights reserved.
level (V
DD
160 of 538
= 3.3 V));