MC68HC908GP16CFB Freescale Semiconductor, MC68HC908GP16CFB Datasheet - Page 129

• Manufacturer Part Number: MC68HC908GP16CFB
• Description: MCU 8-BIT 16K FLASH 44-QFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC68HC908GP16CFB

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 33
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-QFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

13.4.2.1 Character Length
The transmitter can accommodate either 8-bit or 9-bit data. The state of the M bit in ESCI control
register 1 (SCC1) determines character length. When transmitting 9-bit data, bit T8 in ESCI control
register 3 (SCC3) is the ninth bit (bit 8).
13.4.2.2 Character Transmission
During an ESCI transmission, the transmit shift register shifts a character out to the TxD pin. The ESCI
data register (SCDR) is the write-only buffer between the internal data bus and the transmit shift register.
To initiate an ESCI transmission:
At the start of a transmission, transmitter control logic automatically loads the transmit shift register with
a preamble of 1s. After the preamble shifts out, control logic transfers the SCDR data into the transmit
shift register. A 0 start bit automatically goes into the least significant bit (LSB) position of the transmit shift
register. A 1 stop bit goes into the most significant bit (MSB) position.
The ESCI transmitter empty bit, SCTE, in SCS1 becomes set when the SCDR transfers a byte to the
transmit shift register. The SCTE bit indicates that the SCDR can accept new data from the internal data
bus. If the ESCI transmit interrupt enable bit, SCTIE, in SCC2 is also set, the SCTE bit generates a
transmitter CPU interrupt request.
When the transmit shift register is not transmitting a character, the TxD pin goes to the idle condition,
logic 1. If at any time software clears the ENSCI bit in ESCI control register 1 (SCC1), the transmitter and
receiver relinquish control of the port E pins.
13.4.2.3 Break Characters
Writing a 1 to the send break bit, SBK, in SCC2 loads the transmit shift register with a break character.
For TXINV = 0 (output not inverted), a transmitted break character contains all 0s and has no start, stop,
or parity bit. Break character length depends on the M bit in SCC1 and the LINR bits in SCBR. As long as
SBK is at 1, transmitter logic continuously loads break characters into the transmit shift register. After
software clears the SBK bit, the shift register finishes transmitting the last break character and then
transmits at least one 1. The automatic 1 at the end of a break character guarantees the recognition of
the start bit of the next character.
When LINR is cleared in SCBR, the ESCI recognizes a break character when a start bit is followed by
eight or nine 0 data bits and a 0 where the stop bit should be, resulting in a total of 10 or 11 consecutive
0 data bits. When LINR is set in SCBR, the ESCI recognizes a break character when a start bit is followed
by 9 or 10 consecutive 0 data bits and a 0 where the stop bit should be, resulting in a total of 11 or 12
consecutive 0 data bits.
Freescale Semiconductor
1. Enable the ESCI by writing a 1 to the enable ESCI bit (ENSCI) in ESCI control register 1 (SCC1).
2. Enable the transmitter by writing a 1 to the transmitter enable bit (TE) in ESCI control register 2
3. Clear the ESCI transmitter empty bit (SCTE) by first reading ESCI status register 1 (SCS1) and
4. Repeat step 3 for each subsequent transmission.
(SCC2).
then writing to the SCDR. For 9-bit data, also write the T8 bit in SCC3.
MC68HC908EY16 • MC68HC908EY8 Data Sheet, Rev. 10
Functional Description
129