MC68HC908GP16CFB Freescale Semiconductor, MC68HC908GP16CFB Datasheet - Page 230

• Manufacturer Part Number: MC68HC908GP16CFB
• Description: MCU 8-BIT 16K FLASH 44-QFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC68HC908GP16CFB

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 33
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-QFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

Development Support
19.3 Monitor Module (MON)
The monitor module allows debugging and programming of the microcontroller unit (MCU) through a
single-wire interface with a host computer. Monitor mode entry can be achieved without use of the higher
test voltage, V
requirements for in-circuit programming.
Features of the monitor module include:
19.3.1 Functional Description
Figure 19-8
The monitor module receives and executes commands from a host computer.
Figure 19-9
a host computer via a standard RS-232 interface.
Simple monitor commands can access any memory address. In monitor mode, the MCU can execute
code downloaded into RAM by a host computer while most MCU pins retain normal operating mode
functions. All communication between the host computer and the MCU is through the PTA0 pin. A
level-shifting and multiplexing interface is required between PTA0 and the host computer. PTA0 is used
in a wired-OR configuration and requires a pullup resistor.
Table 19-1
may be entered after a power-on reset (POR) and will allow communication at 9600 baud provided one
of the following sets of conditions is met:
1. No security feature is absolutely secure. However, Freescale’s strategy is to make reading or copying the FLASH difficult for
230
unauthorized users.
•
•
•
•
•
•
•
•
•
•
•
•
Normal user-mode pin functionality
One pin dedicated to serial communication between MCU and host computer
Standard non-return-to-zero (NRZ) communication with host computer
Standard communication baud rate (9600 @ 2.4576-MHz bus frequency)
Execution of code in random-access memory (RAM) or FLASH
FLASH memory security feature
FLASH memory programming interface
Monitor mode entry without high voltage, V
$FF)
Normal monitor mode entry if V
If $FFFE and $FFFF do not contain $FF (programmed state):
–
–
If $FFFE and $FFFF contain $FF (erased state):
–
–
If $FFFE and $FFFF contain $FF (erased state):
–
–
The external clock is 9.8304 MHz (9600 baud)
IRQ = V
The external clock is 9.8304 MHz (9600 baud)
IRQ = V
The ICG clock is nominal 1.6 MHz (nominal 6300 baud)
IRQ = V
shows the pin conditions for entering monitor mode. As specified in the table, monitor mode
and
shows a simplified diagram of the monitor mode.
TST
Figure 19-11
, as long as vector addresses $FFFE and $FFFF are blank, thus reducing the hardware
TST
DD
SS
(this can be implemented through the internal IRQ pullup)
MC68HC908EY16 • MC68HC908EY8 Data Sheet, Rev. 10
show example circuits used to enter monitor mode and communicate with
TST
(1)
is applied to IRQ
TST
, if reset vector is blank ($FFFE and $FFFF contain
Freescale Semiconductor