EZ80F91AZ050EG Zilog, EZ80F91AZ050EG Datasheet - Page 55

• Manufacturer Part Number: EZ80F91AZ050EG
• Description: IC ACCLAIM MCU 256KB 144LQFP
• Manufacturer: Zilog
• Series: eZ80® Acclaim!®r

Specifications of EZ80F91AZ050EG

• Core Processor: Z8
• Core Size: 8-Bit
• Speed: 50MHz
• Connectivity: Ethernet, I²C, IrDA, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 144-LQFP
• Processor Series: EZ80F91x
• Core: eZ80
• Data Bus Width: 8 bit
• Data Ram Size: 16 KB
• Interface Type: I2C, IrDA, SPI, UART
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 4
• Operating Supply Voltage: 3 V to 3.6 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: eZ80F910300ZCOG
• Minimum Operating Temperature: - 40 C
• For Use With: 269-4712 - KIT DEV ENCORE 32 SERIES269-4671 - BOARD ZDOTS SBC Z80ACCLAIM PLUS269-4561 - KIT DEV FOR EZ80F91 W/C-COMPILER269-4560 - KIT DEV FOR EZ80F91 W/C-COMPILER
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Details
• Other names: 269-3867; EZ80F91AZ050EG

PS019215-0910
Clock Peripheral Power-Down Registers
•
The CPU is brought out of HALT mode by any of the following operations:
•
•
•
•
•
•
To minimize current in HALT mode, the system clock must be gated-off for all unused 
on-chip peripherals via the Clock Peripheral Power-Down Registers.
HALT Mode and the EMAC Function
When the CPU is in HALT mode, the eZ80F91 device’s EMAC block cannot be disabled
as other peripherals can. On receipt of an Ethernet packet, a maskable Receive interrupt is
generated by the EMAC block, just as it would be in a non-halt mode. Accordingly, the
processor wakes up and continues with the user-defined application.
To reduce power, the Clock Peripheral Power-Down Registers allow the system clock to
be blocked to unused on-chip peripherals. On RESET, all peripherals are enabled. The
clock to unused peripherals are gated off by setting the appropriate bit in the Clock Periph-
eral Power-Down Registers to 1. When powered down, the peripherals are completely dis-
abled. To re-enable, the bit in the Clock Peripheral Power-Down Registers must be cleared
to 0.
Additionally, the VBO_OFF bit of CLK_PPD2 is used to disable the VBO detection cir-
cuit and thereby significantly reduce DC current consumption (see
when this function is not required.
Many peripherals features separate enable/disable control bits that must be appropriately
set for operation. These peripheral specific enable/disable bits do not provide the same
level of power reduction as the Clock Peripheral Power-Down Registers. When powered
down, the individual peripheral control register is not accessible for Read or Write access,
(see
The PC stops incrementing.
A nonmaskable interrupt (NMI).
A maskable interrupt.
A RESET via the external RESET pin driven Low.
A Watchdog Timer time-out (if, configured to generate either an NMI or RESET upon
time-out).
A RESET via execution of a Debug RESET command.
A RESET via the Low-Voltage Brownout detection circuit, if enabled.
Table 4
on page 47 and
Table 5
on page 48).
Product Specification
Table 234
Low-Power Modes
on page 341)
46