s3c4510b Samsung Semiconductor, Inc., s3c4510b Datasheet - Page 296
![no-image](/images/no-image-200.jpg)
s3c4510b
Manufacturer Part Number
s3c4510b
Description
16/32-bit Risc Microcontroller
Manufacturer
Samsung Semiconductor, Inc.
Datasheet
1.S3C4510B.pdf
(422 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
s3c4510b01-QE80
Manufacturer:
BOURNS
Quantity:
400 000
Company:
Part Number:
s3c4510b01-QE80
Manufacturer:
SUNMNG
Quantity:
853
Company:
Part Number:
s3c4510b01-QER0
Manufacturer:
AMCC
Quantity:
156
Part Number:
s3c4510b01-QER0
Manufacturer:
SAMSUMG
Quantity:
20 000
Company:
Part Number:
s3c4510b01-QERO
Manufacturer:
Panasonic
Quantity:
12 000
Company:
Part Number:
s3c4510b01-QERO
Manufacturer:
SAMSUNG
Quantity:
16 615
- Current page: 296 of 422
- Download datasheet (3Mb)
HDLC CONTROLLERS
S3C4510B
In the NRZ/NRZI mode, the DPLL source clock must be 32 times the data rates. In this mode, the transmit and
receive clock outputs of the DPLL are identical, and the clocks are phased so that the receiver samples the data
in the middle of the bit cell.
The DPLL counts the 32x clock using an internal 5-bit counter. As the 32x clock is counted, the DPLL searches
the incoming data stream for edges (either positive or negative transition). The output of DPLL is High while the
DPLL is waiting for an edge in the incoming data stream. When it detects a transition, the DPLL starts the clock
recovery operation.
The first sampling edge of the DPLL occurs at the counter value of 16 after the first edge is detected in the
incoming data stream. The second sampling edge occurs following the next 16. When the transition of incoming
data occurs at a count value other than 16, the DPLL adjusts its clock outputs during the next 0 to 31 counting
cycle by extending or shortening its count by one, which effectively moves the edge of the clock sampling the
receive data closer to the center of the bit cell.
The adding or subtracting of a count of 1 will produce a phase jitter of 5.63 degrees on the output. Because the
DPLL uses both edges of the incoming signal for its clock source comparison, the mark-space ratio (50%) of the
incoming signal must not deviate more than 1.5% of its baud rate if proper locking is to occur.
In the FM mode, the DPLL clock must be 16 times the data rate. The 5-bit counter in the DPLL counts from 0 to
31, so the DPLL makes two sampling clocks during the 0 to 31 counting cycle. The DPLL output is Low while the
DPLL is waiting for an edge in the incoming data stream. The first edge the DPLL detects is assumed to be a
valid clock edge. From this point, the DPLL begins to generate output clocks.
In this mode, the transmit clock output of the DPLL lags the receive clock outputs by 90 degrees to make the
transmit and receive bit cell boundaries the same, because the receiver must sample the FM data at a one-
quarter and three-quarters bit time.
You can program the 32X clock for the DPLL to originate from one of the RxC input pins, from the TxC pin, or
from the baud rate generator output. You can also program the DPLL output to be "echoed out" of the HDLC
module over the TXC pin(if the TXC pin is not being used as an input).
During idle time, you can set the TxPRMB in HCON to send the special pattern required for a remote DPLL to
lock the phase. In this case, the content of the HPRMB register is sent repeatedly. The length of preamble is
determined by TxPL bit in HMODE[10:8].
It is noticed that the frequency of the receive clock (RxC) should be slower than half of the internal system clock
i.e., MCLK/2. Otherwise, the data transfer from receive FIFO to memory could be lost.
8-10
Related parts for s3c4510b
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![irfs630](/images/no-image3.png)
Part Number:
Description:
Transistor,mosfet,n-channel,200v V Br Dss,5.9a
Manufacturer:
Samsung Semiconductor, Inc.
Datasheet:
![KA3S0765R](/images/no-image3.png)
Part Number:
Description:
Samsung Power Switch
Manufacturer:
Samsung Semiconductor, Inc.
Datasheet:
![mmdoe28gxmsp-0va](/images/no-image3.png)
Part Number:
Description:
Samsung Pm410 Ssd 1.8 Lif 128/64gb
Manufacturer:
Samsung Semiconductor, Inc.
Datasheet:
![KA386B](/images/no-image3.png)
Part Number:
Description:
Low Voltage Audio Power Amp
Manufacturer:
Samsung Semiconductor, Inc.
Datasheet:
![KA7226](/images/no-image3.png)
Part Number:
Description:
Dual Equalizer Amplifier With Alc
Manufacturer:
Samsung Semiconductor, Inc.
Datasheet:
![KA78R08](/images/no-image3.png)
Part Number:
Description:
Low Dropout Voltage Regulator
Manufacturer:
Samsung Semiconductor, Inc.
Datasheet:
![KS8620](/images/no-image3.png)
Part Number:
Description:
1 Chip Codec For Digital Answering Phone
Manufacturer:
Samsung Semiconductor, Inc.
Datasheet:
![KS8803B](/images/no-image3.png)
Part Number:
Description:
10/15 Ch Pll
Manufacturer:
Samsung Semiconductor, Inc.
Datasheet:
![ks8701](/images/no-image3.png)
Part Number:
Description:
Flextm Roaming Decoder Ii
Manufacturer:
Samsung Semiconductor, Inc.
Datasheet:
![km68v1000blg-7l](/images/no-image3.png)
Part Number:
Description:
128k X 8bit Low Power And Low Voltage Cmos Statinc Ram
Manufacturer:
Samsung Semiconductor, Inc.
Datasheet:
![ka7522d](/images/no-image3.png)
Part Number:
Description:
Ballast/backlight Controller/driver,sop,20pin,plastic
Manufacturer:
Samsung Semiconductor, Inc.
Datasheet:
![ka2139](/images/no-image3.png)
Part Number:
Description:
3 Channel R.g.b Video Amplifier
Manufacturer:
Samsung Semiconductor, Inc.
Datasheet:
![ka2198bd](/images/no-image3.png)
Part Number:
Description:
Rgb Encoder For Pal/ntsc
Manufacturer:
Samsung Semiconductor, Inc.
Datasheet:
![ka2143b](/images/no-image3.png)
Part Number:
Description:
R/g/b Video Amplifier With Osd Interface For Monitors
Manufacturer:
Samsung Semiconductor, Inc.
Datasheet:
![ka2181](/images/no-image3.png)
Part Number:
Description:
Remote Control Preamplifier
Manufacturer:
Samsung Semiconductor, Inc.
Datasheet: