ATSAM3U-EK Atmel, ATSAM3U-EK Datasheet - Page 468

• Manufacturer Part Number: ATSAM3U-EK
• Description: KIT EVAL FOR AT91SAM3U CORTEX
• Manufacturer: Atmel
• Type: MCUr

Specifications of ATSAM3U-EK

• Contents: Board
• Processor To Be Evaluated: SAM3U
• Data Bus Width: 32 bit
• Interface Type: RS-232, USB
• Operating Supply Voltage: 3 V
• Silicon Manufacturer: Atmel
• Core Architecture: ARM
• Core Sub-architecture: Cortex - M3
• Silicon Core Number: SAM3U4E
• Silicon Family Name: SAM3U
• Kit Contents: Board CD Docs
• Rohs Compliant: Yes
• For Use With/related Products: AT91SAM3U
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

468
SAM3U Series
Note:
• If a new value for CSS field corresponds to PLL Clock,
• If a new value for CSS field corresponds to Main Clock or Slow Clock,
5. Selection of Programmable Clocks
Once the PMC_MCKR register has been written, the user must wait for the MCKRDY bit to
be set in the PMC_SR register. This can be done either by polling the status register or by
waiting for the interrupt line to be raised if the associated interrupt to MCKRDY has been
enabled in the PMC_IER register.
The PMC_MCKR register must not be programmed in a single write operation. The pre-
ferred programming sequence for the PMC_MCKR register is as follows:
If at some stage one of the following parameters, CSS or PRES, is modified, the MCKRDY
bit will go low to indicate that the Master Clock and the Processor Clock are not ready yet.
The user must wait for MCKRDY bit to be set again before using the Master and Processor
Clocks.
Code Example:
The Master Clock is main clock divided by 16.
The Processor Clock is the Master Clock.
Programmable clocks are controlled via registers; PMC_SCER, PMC_SCDR and
PMC_SCSR.
Programmable clocks can be enabled and/or disabled via the PMC_SCER and PMC_SCDR
registers. 3 Programmable clocks can be enabled or disabled. The PMC_SCSR provides a
clear indication as to which Programmable clock is enabled. By default all Programmable
clocks are disabled.
PMC_PCKx registers are used to configure Programmable clocks.
– Program the PRES field in the PMC_MCKR register.
– Wait for the MCKRDY bit to be set in the PMC_SR register.
– Program the CSS field in the PMC_MCKR register.
– Wait for the MCKRDY bit to be set in the PMC_SR register.
– Program the CSS field in the PMC_MCKR register.
– Wait for the MCKRDY bit to be set in the PMC_SR register.
– Program the PRES field in the PMC_MCKR register.
– Wait for the MCKRDY bit to be set in the PMC_SR register.
write_register(PMC_MCKR,0x00000001)
wait (MCKRDY=1)
write_register(PMC_MCKR,0x00000011)
wait (MCKRDY=1)
IF PLLx clock was selected as the Master Clock and the user decides to modify it by writing in
CKGR_PLLR, the MCKRDY flag will go low while PLL is unlocked. Once PLL is locked again,
LOCK goes high and MCKRDY is set.
While PLL is unlocked, the Master Clock selection is automatically changed to Slow Clock. For fur-
ther information, see
Section 28.12.2 “Clock Switching Waveforms” on page
6430D–ATARM–25-Mar-11
471.