AT90CAN32 Automotive Atmel Corporation, AT90CAN32 Automotive Datasheet - Page 187

• Manufacturer Part Number: AT90CAN32 Automotive
• Manufacturer: Atmel Corporation

Specifications of AT90CAN32 Automotive

• Flash (kbytes): 32 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 53
• Ext Interrupts: 8
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Uart: 2
• Can: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 2
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 125
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 8
• Input Capture Channels: 2
• Pwm Channels: 7
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

7682C–AUTO–04/08
The following code example shows a simple USART0 receive function that handles both nine bit
characters and the status bits.
Note:
The receive function example reads all the I/O Registers into the Register File before any com-
putation is done. This gives an optimal receive buffer utilization since the buffer location read will
be free to accept new data as early as possible.
Assembly Code Example
C Code Example
USART0_Receive:
USART0_ReceiveNoError:
unsigned int USART0_Receive(void)
{
}
; Wait for data to be received
lds
sbrs
rjmp
; Get status and 9th bit, then data from buffer
lds
lds
; If error, return -1
andi
breq
ldi
ldi
; Filter the 9th bit, then return
lsr
andi
ret
unsigned char status, resh, resl;
/* Wait for data to be received */
while ( ! (UCSR0A & (1<<RXC0)));
/* Get status and 9th bit, then data */
/* from buffer */
status = UCSR0A;
resh = UCSR0B;
resl = UDR0;
/* If error, return -1 */
if ( status & (1<<FE0)|(1<<DOR0)|(1<<UPE0) )
/* Filter the 9th bit, then return */
resh = (resh >> 1) & 0x01;
return ((resh << 8) | resl);
1. The example code assumes that the part specific header file is included.
return -1;
r18, UCSR0A
r18, RXC0
USART0_Receive
r17, UCSR0B
r16, UDR0
r18, (1<<FE0) | (1<<DOR0) | (1<<UPE0)
USART0_ReceiveNoError
r17, HIGH(-1)
r16, LOW(-1)
r17
r17, 0x01
(1)
(1)
AT90CAN32/64/128
187