AT90CAN32 Automotive Atmel Corporation, AT90CAN32 Automotive Datasheet - Page 254

• Manufacturer Part Number: AT90CAN32 Automotive
• Manufacturer: Atmel Corporation

Specifications of AT90CAN32 Automotive

• Flash (kbytes): 32 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 53
• Ext Interrupts: 8
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Uart: 2
• Can: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 2
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 125
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 8
• Input Capture Channels: 2
• Pwm Channels: 7
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

19.10.4
254
AT90CAN32/64/128
CAN General Interrupt Enable Register - CANGIE
• Bit 2 – CERG: CRC Error General
Writing a logical one resets this interrupt flag.
• Bit 1 – FERG: Form Error General
Writing a logical one resets this interrupt flag.
• Bit 0 – AERG: Acknowledgment Error General
Writing a logical one resets this interrupt flag.
• Bit 7 – ENIT: Enable all Interrupts (Except for CAN Timer Overrun Interrupt)
• Bit 6 – ENBOFF: Enable Bus Off Interrupt
• Bit 5 – ENRX: Enable Receive Interrupt
• Bit 4 – ENTX: Enable Transmit Interrupt
• Bit 3 – ENERR: Enable MOb Errors Interrupt
Initial Value
Read/Write
Bit
– 1 - stuff error interrupt: detection of more than 5 consecutive bits with the same
– 0 - no interrupt.
– 1 - CRC error interrupt: the CRC check on destuffed message does not fit with the
– 0 - no interrupt.
– 1 - form error interrupt: one or more violations of the fixed form in the CRC delimiter,
– 0 - no interrupt.
– 1 - acknowledgment error interrupt: no detection of the dominant bit in acknowledge
– 0 - interrupt disabled.
– 1- CANIT interrupt enabled.
– 0 - interrupt disabled.
– 1- bus off interrupt enabled.
– 0 - interrupt disabled.
– 1- receive interrupt enabled.
– 0 - interrupt disabled.
– 1- transmit interrupt enabled.
– 0 - interrupt disabled.
– 1- MOb errors interrupt enabled.
polarity.
CRC field.
acknowledgment delimiter or EOF.
slot.
ENIT
R/W
7
0
ENBOFF
R/W
6
0
ENRX
R/W
5
0
ENTX
R/W
4
0
ENERR
R/W
3
0
ENBX
R/W
2
0
ENERG
R/W
1
0
ENOVRT
R/W
0
0
CANGIE
7682C–AUTO–04/08