AT90CAN32 Automotive Atmel Corporation, AT90CAN32 Automotive Datasheet - Page 243

• Manufacturer Part Number: AT90CAN32 Automotive
• Manufacturer: Atmel Corporation

Specifications of AT90CAN32 Automotive

• Flash (kbytes): 32 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 53
• Ext Interrupts: 8
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Uart: 2
• Can: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 2
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 125
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 8
• Input Capture Channels: 2
• Pwm Channels: 7
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

19.5.1.1
19.5.1.2
19.5.1.3
7682C–AUTO–04/08
Disabled
Tx Data & Remote Frame
Rx Data & Remote Frame
Table 19-1.
In this mode, the MOb is “free”.
1. Several fields must be initialized before sending:
2. The MOb is ready to send a data or a remote frame when the MOb configuration is set
3. Then, the CAN channel scans all the MObs in Tx configuration, finds the MOb having
4. When the transmission is completed the TXOK flag is set (interrupt).
5. All the parameters and data are available in the MOb until a new initialization.
1. Several fields must be initialized before receiving:
2. The MOb is ready to receive a data or a remote frame when the MOb configuration is
3. When a frame identifier is received on CAN network, the CAN channel scans all the
4. On a hit, the IDT, the IDE and the DLC of the matched MOb are updated from the
5. Once the reception is completed, the data bytes of the received message are stored
MOb Configuration
1
1
– Identifier tag (IDT)
– Identifier extension (IDE)
– Remote transmission request (RTRTAG)
– Data length code (DLC)
– Reserved bit(s) tag (RBnTAG)
– Data bytes of message (MSG)
(CONMOB).
the highest priority and tries to send it.
– Identifier tag (IDT)
– Identifier mask (IDMSK)
– Identifier extension (IDE)
– Identifier extension mask (IDEMSK)
– Remote transmission request (RTRTAG)
– Remote transmission request mask (RTRMSK)
– Data length code (DLC)
– Reserved bit(s) tag (RBnTAG)
set (CONMOB).
MObs in receive mode, tries to find the MOb having the highest priority which is
matching.
incoming (frame) values.
(not for remote frame) in the data buffer of the matched MOb and the RXOK flag is set
(interrupt).
MOb Configuration (Continued)
0
1
Reply Valid
0
1
x
x
RTR Tag
0
1
x
Operating Mode
Rx Data Frame
Rx Remote Frame
Rx Remote Frame then, Tx Data Frame (reply)
Frame Buffer Receive Mode
AT90CAN32/64/128
243