cx28394 Conexant Systems, Inc., cx28394 Datasheet - Page 183

• Manufacturer Part Number: cx28394
• Description: Quad/x16/octal-t1/e1/j1 Framers
• Manufacturer: Conexant Systems, Inc.

CX28394/28395/28398
Quad/x16/Octal—T1/E1/J1 Framers
TFRM controls the insertion of overhead bits generated by transmit frame and alarm formatters. Bypassed
overhead bits flow transparently from TPCMI system bus input through TSLIP buffer.
INS_MYEL
INS_YEL
INS_MF
INS_FE
INS_CRC
INS_FBIT
100054E
072—Transmit Frame Format (TFRM)
Unused bits are reserved and should be written to 0.
—
7
Insert Multiframe Yellow Alarm—Applicable to E1 modes only. Enables the alarm formatter
to output Y16 Multiframe Yellow Alarm. Once enabled, TMYEL and AUTO_MYEL [addr
075] control the alarm output state. This bit must be set to 0 in T1 modes.
Insert Yellow Alarm—The alarm formatter outputs yellow alarms YB2 or YJ during T1
modes; or Y0 during E1 modes. In ESF framed T1 mode, the YF Yellow Alarm is transmitted
by programming the DL1 data link controller and by transmitting the appropriate bit oriented
code message (BOP message). Once enabled, TYEL and AUTO_YEL [addr 075] control the
yellow alarm output state. If the system wants to bypass JYEL (Fs bit in frame 12), then it must
bypass all Fs bits with INS_MF [addr 072].
Insert Multiframe Alignment—The frame formatter outputs 6-bit SF alignment pattern in T1
mode, or 6-bit MFAS alignment pattern in E1 mode. INS_MF should be set while TFRAME
(addr 070) selects Fs (T1) or MFAS (E1) alignment.
Insert FEBE— During E1 mode, the alarm formatter automatically outputs TS0 bit 1 of frame
13 (FEBE13) and frame 15 (FEBE15) in response to received CRC4 errors. FEBE13 is active
low for each received CRC4 error detected in SMF I. FEBE15 is active low for each received
CRC4 error detected in SMF II. INS_FE should be set while TFRAME (addr 070) selects
FEBE (E1) alignment.
Insert Cyclic Redundancy Check—The frame formatter outputs the calculated CRC6 bits in
T1 mode or CRC4 bits in E1 mode.
Insert Terminal Framing—The frame formatter outputs a 2-bit Ft alignment pattern in F-bits of
odd frames (SF framing) or FPS framing pattern (ESF framing) during T1 modes—or 8-bit
FAS/NFAS alignment pattern during E1 modes. INS_FBIT should be set while TFRAME
(addr: 070) selects Ft (T1, SF), FPS (T1, ESF), or FAS (E1) alignment.
If F-bits are bypassed while TSLIP is enabled, the system must either use embedded T1
framing or apply at least a double frame (250 s) multiframe sync pulse (TMSYNC) to
provide odd/even frame alignment.
—
0 = bypass
1 = insert multiframe yellow alarm
0 = bypass
1 = insert yellow alarm.
0 = bypass
1 = insert multiframe alignment
0 = bypass
1 = insert FEBE
0 = bypass
1 = insert cyclic redundancy check
0 = bypass
1 = insert terminal framing
6
INS_MYEL
5
INS_YEL
4
Conexant
INS_MF
3
INS_FE
2
INS_CRC
3.12 Transmitter Registers
1
3.0 Registers
INS_FBIT
0
3-61