cx28394 Conexant Systems, Inc., cx28394 Datasheet - Page 70

• Manufacturer Part Number: cx28394
• Description: Quad/x16/octal-t1/e1/j1 Framers
• Manufacturer: Conexant Systems, Inc.

2.0 Circuit Description
2.2 Receiver
Table 2-2. Criteria for Loss/Recovery of Receive Framer Alignment
2-12
FAS
BSLIP
MFAS
CAS
F T Only
Mode
Basic Frame Alignment (BFA) is recovered when the following search criteria are satisfied:
During FAS-only modes, BFA is recovered when the following search criteria are satisfied:
NOTE(S):
frame N+2.
Loss of FAS frame alignment (FRED) is declared when one of the following criteria is met:
NOTE(S):
FAS Bit Slip Enable. Applicable only for Dutch PTT national applications. If BSLIP is enabled, the online framer
is allowed to change RX timebase by 1 bit when a 1-bit FAS pattern slip is detected. BSLIP does not affect the
offline framer's search criteria.
CRC4 Multiframe Alignment is recovered when the following search criteria are satisfied:
Loss of MFAS alignment (MRED) declared when one of the following criteria is met:
NOTE(S):
CAS Multiframe Alignment is recovered when the following search criteria are satisfied:
Loss of CAS alignment (SRED) is declared when one of the following criteria is met:
Terminal frame alignment is recovered when:
193 bits.
During Ft-only mode, loss of frame alignment (FRED) is declared when:
The first valid Ft pattern (1010) is found in 12 alternate F-bit locations (3 ms), where F-bits are separated by
Number of Ft bit errors detected meets selected loss of frame criteria [RLOFA–RLOFC; addr 040].
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
FAS pattern (0011011) is found in frame N.
Frame N+1 contains bit 2 equal to 1.
Frame N+2 also contains FAS pattern (0011011).
FAS pattern (0011011) is found in frame N.
No mimics of the FAS pattern are present in frame N+1.
FAS pattern (0011011) is found in frame N+2.
Three consecutive FAS pattern errors are detected when the FAS pattern consists of a 7-bit (x0011011)
pattern in FAS frames and—if FS_NFAS is also active [addr 045]—the FAS pattern includes bit 2 of
NFAS frames.
Loss of MFAS (MRED) is due to 915 or more CRC errors out of 1000.
Failure to locate two valid MFAS patterns within 8 ms after BFA.
BFA is recovered, identifying FAS and NFAS frames.
Within 8 ms after BFA, bit 1 of NFAS frames contains two MFAS patterns (001011xx). The second
MFAS must be aligned with respect to first MFAS, but the second MFAS pattern is not necessarily
received in consecutive frames.
Within 8 ms after BFA, bit 1 of NFAS frames contains the second MFAS pattern (001011xx), aligned to
first MFAS.
915 or more CRC4 errors out of 1000 (submultiframe) blocks.
Loss of FAS (FRED).
BFA is recovered, identifying TS0 through TS31.
MAS (0000xxxx) multiframe alignment signal pattern is found in the first 4 bits of TS16, and 8 bits of
TS16 in preceding frame contains nonzero value.
Two consecutive MAS pattern errors are detected.
TS16 contains all zeros in two multiframes (32 consecutive frames).
Loss of FAS (FRED).
If FAS pattern is not found in frame N+2, or if FAS mimic is found in frame N+1, the search restarts in
In all cases, FRED causes next search for FAS alignment to begin 1 bit after the current FAS location.
If Disable 915 CRC Reframe is set [RLOFD; addr 040], then MRED is activated only by FRED.
Conexant
Description
Quad/x16/Octal—T1/E1/J1 Framers
CX28394/28395/28398
100054E