MC68HC908JG16FA MOTOROLA [Motorola, Inc], MC68HC908JG16FA Datasheet - Page 172
MC68HC908JG16FA
Manufacturer Part Number
MC68HC908JG16FA
Description
Microcontrollers
Manufacturer
MOTOROLA [Motorola, Inc]
Datasheet
1.MC68HC908JG16FA.pdf
(324 pages)
- Current page: 172 of 324
- Download datasheet (3Mb)
Universal Serial Bus Module (USB)
11.5.3 Suspend
Technical Data
172
NOTE:
The reset flag bit (RSTF) in the USB interrupt register 1 (UIR1) also will
be set after the internal reset is removed. Refer to
Register 1
After a reset is removed, the device will be in the default, but not yet
addressed or configured state (refer to Section 9.1 USB Device States
of the Universal Serial Bus Specification Rev. 2.0). The device must be
able to accept a device address via a SET_ADDRESS command (refer
to Section 9.4 Standard Device Request in the Universal Serial Bus
Specification Rev. 2.0) no later than 10ms after the reset is removed.
Reset can wake a device from the suspended mode.
USB reset can be configured not to generate a reset signal to the CPU
by setting the URSTD bit of the configuration register (see
Configuration Register
CPU generates an USB interrupt.
The MCU supports suspend mode for low power. Suspend mode should
be entered when the USB data lines are in the idle state for more than
3ms. Entry into suspend mode is controlled by the SUSPND bit in the
USB interrupt register. Any low-speed bus activity should keep the
device out of the suspend state. Low-speed devices are kept awake by
periodic low-speed EOP signals from the host. This is referred to as low
speed keep alive (refer to Section 11.8.4.1 Low-speed Keep-alive in the
Universal Serial Bus Specification Rev. 2.0).
Firmware should monitor the EOPF flag and enter suspend mode by
setting the SUSPND bit if an EOP is not detected for 3ms.
Per the USB specification, the bus powered USB system is required to
draw less than 500 A from the V
This includes the current supplied by the voltage regulator to the 1.5k
to ground termination resistors placed at the host end of the USB bus.
This low-current requirement means that firmware is responsible for
entering stop mode once the USB module has been placed in the
suspend state.
Freescale Semiconductor, Inc.
For More Information On This Product,
Universal Serial Bus Module (USB)
for more detail.
Go to: www.freescale.com
(CONFIG)). When a USB reset is detected, the
DD
supply when in the suspend state.
MC68HC908JG16
11.8.3 USB Interrupt
Section 5.
MOTOROLA
—
Rev. 1.0
Related parts for MC68HC908JG16FA
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Motorola, Inc [VOLTAGE REGULATOR]
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
6367254 MOTOROLA SC (XSTRS/R F)
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
MC1494LMotorola, Inc [MONOLITHIC FOUR-QUADRANT MULTIPLIER]
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
MC1466LMotorola, Inc [PRECISION WIDE RANGE VOLTAGE AND CURRENT REGULATOR]
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
MC145532DWMotorola, Inc [ADPCM Transcoder]
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
Silicon Controlled Rectifiers
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
RF Power Field Effect Transistors N-Channel Enhancement-Mode Lateral MOSFETs
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
RF POWER FIELD EFFECT TRANSISTORS
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
LATERAL N-CHANNEL BROADBAND RF POWER MOSFETs
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
RF POWER FIELD EFFECT TRANSISTOR
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
RF LOW POWER TRANSISTOR NPN SILICON
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
PLASTIC SURFACE MOUNT ZENER DIODES 1.5 WATTS 3.3-68 VOLTS
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
OVERVOLTAGE TRANSIENT SUPPRESSOR
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
TMOS POWER FET 15 AMPERES 60 VOLTS
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
TMOS POWER FET LOGIC LEVEL 19 AMPERES 30 VOLTS RDS(on) = 0.099 OHM
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet: