R88M-WP20030H-BW Omron, R88M-WP20030H-BW Datasheet - Page 276

• Manufacturer Part Number: R88M-WP20030H-BW
• Description: SERVO MOTOR 200W 200V W/BRAKE
• Manufacturer: Omron

Specifications of R88M-WP20030H-BW

• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: R88MWP20030HBW

Operation
• When set to 7, the servo turns ON after the power has been turned ON. You cannot use the jog opera-
• Settings are the same as for Pn50A.1.
• If Pn50A.0 is set to 0, you cannot change the pin number. Settings 0 to 6 and 9 to F are disabled, and all
• To change the pin number, set Pn50A.0 to 1.
• Settings are the same as for Pn50A.1.
• If Pn50A.0 is set to 0, you cannot change the pin number. Settings 0 to 6 and 9 to F are disabled, and all
• To change the pin number, set Pn50A.0 to 1.
• If set to 7 (always ON), the servo is in always overtravel status (i.e., forward rotation is always drive-
• If set to 8 (always OFF), the servo drive prohibition is OFF (i.e., the forward rotation drive is permitted).
• The POT signal permits forward rotation drive upon input.
• Settings are the same as for Pn50A.1.
• If Pn50A.0 is set to 0, you cannot change the pin number. Settings 0 to 6 and 9 to F are disabled, and all
• To change the pin number, set Pn50A.0 to 1.
• If set to 7 (always ON), the servo is in always in overtravel status (i.e., reverse rotation is always drive-
• If set to 8 (always OFF), the servo drive prohibition is OFF (i.e., the reverse rotation drive is permitted).
• The NOT signal permits reverse rotation drive upon input.
• Settings are the same as for Pn50A.1.
• If Pn50A.0 is set to 0, you cannot change the pin number. Settings 0 to 6 and 9 to F are disabled, and all
• To change the pin number, set Pn50A.0 to 1.
4-38
Pn50A.2
Setting
range
Pn50A.3
Setting
range
Pn50b.0
Setting
range
Pn50b.1
Setting
range
tion with this setting.
are set to CN1, pin 41 enabled by L input. Settings 7 and 8 are both enabled.
are set to CN1, pin 42 enabled by L input. Settings 7 and 8 are both enabled.
prohibited).
are set to CN1, pin 43 enabled by L input. Settings 7 and 8 are both enabled.
prohibited).
are set to CN1, pin 44 enabled by L input. Settings 7 and 8 are both enabled.
Input signal selection 1 –– MING signal (gain reduction) input terminal allocation (Position,
speed, internally-set speed control)
0 to F
Input signal selection 1 –– POT signal (forward drive prohibited) input terminal allocation (All
operation modes)
0 to F
Input signal selection 2 –– NOT signal (reverse drive prohibited) input terminal allocation (All
operation modes)
0 to F
Input signal selection 2 –– RESET signal (alarm reset) input terminal allocation (All operation
modes)
0 to F
Unit
Unit
Unit
Unit
---
---
---
---
Default
setting
Default
setting
Default
setting
Default
setting
1
8
8
4
Restart
power?
Restart
power?
Restart
power?
Restart
power?
Chapter 4
Yes
Yes
Yes
Yes