SC1200UFH-266 AMD (ADVANCED MICRO DEVICES), SC1200UFH-266 Datasheet - Page 225

• Manufacturer Part Number: SC1200UFH-266
• Manufacturer: AMD (ADVANCED MICRO DEVICES)

Specifications of SC1200UFH-266

• Operating Temperature (min): 0C
• Operating Temperature (max): 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Lead Free Status / Rohs Status: Not Compliant

Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
AMD Geode™ SC1200/SC1201 Processor Data Book
Offset 10h-13h
Offset 14h-17h
Offset 18h-1Bh
Offset 1Ch-1Fh
Offset 20h-23h
31:16
31:16
31:0
31:0
15:0
15:0
31:6
Bit
Description
GPIO Data Out. Bits [31:0] of this register correspond to GPIO63-GPIO32 signals, respectively. The value of each bit deter-
mines the value driven on the corresponding GPIO signal when its output buffer is enabled. Writing to the bit latches the
written data unless the bit is locked by the GPIO Configuration register Lock bit (F0BAR0+I/O Offset 24h[3]). Reading the
bit returns the value, regardless of the signal value and configuration.
0: Corresponding GPIO signal driven to low when output enabled.
1: Corresponding GPIO signal driven or released to high (according to buffer type and static pull-up selection) when output
GPIO Data In. Bits [31:0] of this register correspond to GPIO63-GPIO32 signals, respectively. Reading each bit returns the
value of the corresponding GPIO signal, regardless of the signal configuration and the GPDO1 register (F0BAR0+I/O Offset
10h) value. Writes to this register are ignored.
0: Corresponding GPIO signal level low.
1: Corresponding GPIO signal level high.
Reserved. Must be set to 0.
GPIO Power Management Event (PME) Enable. Bits [15:0] of this register correspond to GPIO47-GPIO32 signals,
respectively. Each bit allows PME generation by the corresponding GPIO signal.
0: Disable PME generation.
1: Enable PME generation.
Notes: 1) All of the enabled GPIO PMEs are always reported at F1BAR1+I/O Offset 10h[3].
Reserved. Must be set to 0.
GPIO Status. Bits [15:0] correspond to GPIO47-GPIO32 signals, respectively. Each bit reports a 1 when hardware detects
the edge (rising/falling on the GPIO signal) that is programmed in F0BAR0+I/O Offset 24h[5]. If the corresponding bit in
F0BAR0+I/O Offset 18h is set, this edge generates a PME.
0: No active edge detected since the bit was last cleared.
1: Active edge detected.
Writing 1 to the a Status bit clears it to 0.
This is the third level of SMI status reporting to the second level at F0 Index 87h/F7h[7] and the top level at F1BAR0+I/O
Offset 00h/02h[0]. Clearing the third level also clears the second and top levels.
This is the second level of SCI status reporting to the top level at F1BAR1+Offset 10h[3]. The status must be cleared at both
the this level and the top level (i.e., the top level is not automatically cleared when a bit in this register is cleared).
Reserved. Must be set to 0.
enabled.
Table 6-30. F0BAR0+I/O Offset: GPIO Configuration Registers (Continued)
2) Any enabled GPIO PME can be selected to generate an SCI or SMI at F1BAR1+I/O Offset 0Ch[0].
If SCI is selected, the individually selected GPIO PMEs are globally enabled for SCI generation at F1BAR1+I/
O Offset 12h[3] and the status is reported at F1BAR1+I/O Offset 10h[3].
If SMI is selected, the individually selected GPIO PMEs generate an SMI and the status is reported at
F1BAR0+I/O Offset 00h/02h[0].
GPIEN1 — GPIO Interrupt Enable 1 Register (R/W)
GPIO Signal Configuration Select Register (R/W)
GPDO1 — GPIO Data Out 1 Register (R/W)
GPST1 — GPIO Status 1 Register (R/W1C)
GPDI1 — GPIO Data In 1 Register (RO)
32579B
Reset Value: FFFFFFFFh
Reset Value: FFFFFFFFh
Reset Value: 00000000h
Reset Value: 00000000h
Reset Value: 00000000h
225